answersLogoWhite

0

  • Auto Parts and Repairs
  • Mufflers and Tailpipes
  • Air Filters and Intake Manifolds
  • Chevy 350

What are the bolt torque values for the exhaust manifold to Y pipe on a 95 Astro Van 4.3L?

User Avatar

Wiki User

βˆ™ 2004-10-18 14:41:31

Best Answer
Copy

It should be about 45 ftlb

2004-10-18 14:41:31
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Your Answer

Loading...

Related Questions

How do you change the exhaust manifold gasket on a 93 Chevy astro van?

You will need to remove the exhaust manifold retaining bolts in your 1993 Chevy Astro. Remove the exhaust manifold. Remove the exhaust manifold gasket and clean the surface. Reverse the process to install the new exhaust manifold gasket.


Where is the oxygen sensor for a 91 Astro AWD Van?

I know that one of them is located on the exhaust manifold, between the point where the left and right exhaust manifolds merge and the catalytic converter. But I am not sure if there is a second one.


1989 Chevy Astro Van has a coolant leak at the fitting were the heater circuit pipe attaches to the intake manifold near the distributor How does this fittings come apart?

It snaps in. But before you snap it out, take the nut out that holds the pipe to the exhaust manifold.


Where is the upstream oxygen sensor located and can you replace it yourself?

The upstream o/2 sensor is located in the exhaust system between the exhaust manifold and the catalytic converter. Some vehicles will have 2 upstream sensors (i.e. 1999 Chevy astro 4.3l engine has sensor for left exhaust manifold and another for right exhaust manifold). I am trying to find out for sure if you have to replace both when one goes bad. Bosch says both must be replaced!!!??? Oh yeah it(they)are easy enough to replace if you can see it (them).


How to replace the Intake manifold gasket on a 1996 Chevy Astro?

Remove the intake manifold retaining bolts from your 1996 Chevy Astro Van. Remove the manifold gasket and clean the surface. Reverse the process to install the new intake manifold gasket.


Where are the 02 sensors on a 1996 astro van?

The 1999 has three O2 sensors. One in each of the exhaust pipes coming off of the manifold and a third after the catalytic converter. Not sure if the 96 is the same or not.


Head gasket torque specs 4.3 Chevy astro?

The 4.3 liter Chevy Astro head gasket torque specification is 160 pounds. The head gasket bolts should be torqued in 40 pound intervals.


How much horsepower does a 98 astro van have?

190 hp and 250 Ibs of torque


How many o2 sensors on a 2002 Astro?

If the 8th digit on your vin number is an X as mine is there are 3 oxygen sensors. I don't have dual exhaust so I have one o2 sensor below each manifold (visible from underneath the van) and one after the catalytic converter.


1994 Chevy astro fuel regulator location?

it is part of the fuel injector which is under the upper intake manifold


Where is the starter on a 1993 astro van?

right side(passanger side) of engine under the exhaust manafold.


What is the correct 1986 Chevy van wheel torque in Nm's?

Astro and Safari 100 ft. lbs.


Where is the PVC valve on a 2002 Chevy Astro van?

Check pass. side middle of manifold cover. runs about 10$


Where is the vacuum line for heater on 1996 astro van?

Most all of the vacuum lines will start from the intake manifold in the rear..........


1986 Chevy Astro Van V6 43 hesitating on take off but then runs fine after that?

I think it's your EGR Valve. The EGR valve, or Exhaust Gas Recirculation valve, is a vacuum controlled valve which allows a specific amount of your exhaust back into the intake manifold.The EGR valve, or Exhaust Gas Recirculation valve, is a vacuum controlled valve which allows a specific amount of your exhaust back into the intake manifold. You'll know if your EGR valve is stuck or malfunctioning because your car will experience symptoms like rough idle and bucking on acceleration.


Air conditioning blows through windshield vent instead of interior vents on Chevrolet Astro?

The vents are controlled by vaccuum from the intake manifold. Check for a split rubber vac. hose on the manifold- Hope that helps.


Where is the Fuel Injector Pressure Regulator located on 01 Chevy astro?

It is inside the upper intake manifold. It is attached to the fuel injector poppets with a bracket. To inspect/replace you must remove the upper intake manifold.


Your 1986 astro van is not getting fuel and it has a new fuel pump you had the exhaust welded and it hasent started since?

If your exhaust pipes by engine get red hot you have a vacuum leak that will make it sluggish


Where is the oxygen sensor located on a 2000 astro van?

They are located in the exhaust system, rearward of the manifolds, and again after the catalytic converter.


Where is the location of O2 sensor 1995 Chevy Astro?

1995 Chevrolet Astro, 4.3 V6 engine with Single Point Injection System has one O2 sensor located in exhaust pipe (between catalitic converter and the place where exhaust pipes from right and left cylinder heads meets in one pipe).


Where is fuel pressure regulator located on 1998 Chevy astro van?

It's part of the fuel injection assembly inside the upper manifold.


Can a blown intake manifold gasket cause a 1994 Chevy Astro to run rich and foul the plugs?

That would probably cause it to run lean.


Where is temp sending unit on 1999 Astro Van with stock V-6?

To the left of the water inlet housing (thermostat housing) on the intake manifold


Where can you get a vacuum diagram for the rear heater control valve for 97 astro van?

vacume line to the valve has broke off from manifold vac that goes to the switch


What does code 45 Rich exhaust indicated mean in 1992 Chevy Astro?

check evaporative charcoal canister and its componants for fuel.replace oxygen sensor,