answersLogoWhite

0


Best Answer

a) Bolts 1 - 14) 22 ft lbs b) Bolts 1 - 14) 45 ft lbs c) check all are at 45 ft lbs d) Bolts 1-10) 110 ft lbs e) Bolts 11-13) 100 ft lbs f) Bolts 12-14) 110 ft lbs From the front, bolt #'s are... 12, 8, 4, 1, 5, 9, 13 11, 7, 3, 2, 6, 10, 14 12 & 11 are at front 13 & 14 are at rear Notes: Hold 14 up with tape. Use loctite 592 on bolt 11

User Avatar

Wiki User

16y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

15y ago

Torquing the cylinder head bolts is a multistep process in order in ensure that the heads are tightened evenly around the whole head. So:

Step one: 11 mm bolts 1 - 10 tighten to 15 ft lbs

Step two: 11 mm bolts 1 - 10 tighten to 35 ft lbs

Step three: 8 mm bolts 11 - 14 tighten to 18 ft lbs

Step four: 11 mm bolts 1 - 10 turn an additional 90 degrees (1/4 turn)

Step five: 8 mm bolts 11 - 14 tighten to 22 ft lbs

Hope this helps.

Good luck !!

This answer is:
User Avatar

User Avatar

Wiki User

14y ago

Torque settings are 110 ft LBS for nine of the ten bolts one bolt is 100 ft LBS /#1 Tighten all bolts in sequence 1 to 10 at 22 ft LBS #2 tighten all bolts 1 to 10 at 45 ft LBS #3 tighten all bolts 1 to 6 at 110 ft LBS #4 bolt #7 at 100 ft LBS #5 BOLT 8 TO 10 AT 110 FT LBS . HEAD TIGHTEN SEQUENCE - standing at front of car bolts down left side are 8/4/1/5/9 bolts down right side are 7/3/2/6/10. left side meaning distributor side.

This answer is:
User Avatar

User Avatar

Wiki User

12y ago

Work from center out alternating, snug up, torque to 55in pounds or 4.55 ftlbs.

This answer is:
User Avatar

User Avatar

Wiki User

14y ago

85-105 foot pounds for wheel lugs and you torque in a star pattern

This answer is:
User Avatar

User Avatar

Wiki User

14y ago

You should refer to repair manual, clean threads in block as well as mating surfaces and use new head bolts and gasket

This answer is:
User Avatar

User Avatar

Wiki User

9y ago

The Jeep Cherokee 4.0 liter engine cylinder had torque specifications are 120 pounds per square inch. The cylinder head bolts should be torqued at 40 pound intervals.

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What are the cylinder head bolt torque settings on a 2001 Jeep Grand Cherokee 4.7L V8 engine?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What are the cylinder head bolt torque settings on a 2001 Jeep Cherokee 3.7L V6 engine?

The 2001 Jeep Cherokee 3.7 liter engine cylinder had bolt torque specification is 150 pounds. The cylinder head bolts should be torqued in 50 pound intervals.


What are the torque settings for the cylinder head Mitsubishi Rosa engine model 4M51?

what are the torque settings for a mitsubishi 4m51 engine


What are the cylinder head bolt torque settings on an Isuzu kb 250 4ja engine?

What are cylinder head bolts torque settings for Isuzu kb240. Engine NAQ001716


What are the cylinder head bolt torque settings on a volkswagen polo aev engine code?

polo torque settings 1200 engine main bearing


What are the torque specifications for a Subaru Outback 2.0 TD engine?

You need to specify which torque settings. As with any vehicle, torque settings are specific to a particular part of the vehicle.The torque settings for the cylinder head will differ from the settings for the crankshaft bearings.


What are cylinder head torque settings on a daewoo espero?

Torque settings daewoo espero cylinder


What are the cylinder head bolt torque settings on a 1998 jeep grand Cherokee 5 point 2 L V8 engine?

85 ft/lbs


Head cylinder torque setting Isuzu bighorn 4jg2 engine?

torque settings are: 4JG2 cylinder head, 49 Nm + 60 degrees + 60 degrees.


Torque settings for megane 1600 k4m?

torque settings for cylinder head bolts


What are the cylinder head torque settings for a Toyota 2E engine?

30 NM 50 NM then 90°


What are the cylinder head torque settings for a Mazda bongo 2.5 turbo diesel 1997?

what are the torque for camshaft and cylinder head bolts please


What are the torque settings for an au 6-cylinder falcon with vct?

pressure plate torque settings for ford falcon au 6 cylinder