Torque to 95 foot pounds with thread locking compound.
What are the torque specs for a flywheel and pressure plate on a Datsun 240Z
what are the torque specs for the flywheel on a 92 ford ranger?
what are the torque specs for clutch and fly wheel model 5700
Depends on the engine.
need torque specs for 3.4 pontiac grand am intake and rocker arms
185 foot pounds
The short bolt torque specs for the head gasket of a 2000 Pontiac Sunfire is 43 foot pounds. The torque specs for long bolts is 46 foot pounds.
55 flywheel to crank 70 flexplate to crank
For your 1992 Nissan/Datsun 300ZX: Flywheel Torque 61-69 Foot pounds (Final torque)
depends on the engine size the 4.6 flywheel to crank is 62lbs and pressure plate to flywheel is 18lbs
Pressure plate to flywheel torque is (ft lbs) 14 to 20.
I believe that these specs do vary from model to model, but here are the specs for a 97-01 Prelude. Pressure plate bolts - 19 lb ft Flywheel bolts - 76 lb ft
80Lbs for flywheel, 10 to 15lbs for pressure plate
90 ft lbs is the standard torque on most flywheels
If you pick up a Haynes or Chilton manual for your car, it will contain all the torque specs you need. FriPilot
about 2302 ft/lbs
1.6 1.8 2.0Ltr All 120/130Nm.
80 ft pounds
25 ft lbs on pressure plate and 50 Ft lbs on the flywheel bolts. use locktite
Pick up a Haynes or Chilton manual for the car. It will have those torque specs as well as many others.
Flywheel must be torqued to 105 ft/lbs. Clutch and pressure plate torqued to 22 ft/lbs.
Not really sure if you are asking about the oil pan torque, it's 12lbs. see link for other torque specs.
44.25lb +90 degrees for 22.5mm bolts or +180 deggres for 45mm.
The Specs on the Solstice GXP are: 5 x 110mm bolt pattern 55mm Offset 18" x 8" size
The best way to get the torque specs is by purchasing a Haynes manual. They can be picked up for 10 to 20 dollars, and they have all the specs for bolt torque for the entire fastening system on the vehicle, as well as volumes for oils etc.
If you mean engine performance, then it has 240 hp and 280 lbs of torque
The torque specs for a 235 Chevy include main cap bolts of 100 - 110. Its bellhousing bolts are 45 - 55, flywheel bolts of 50 - 65, and rod nuts of 35 - 45.
Flywheel 79.7ft lbs - 85.5 ft lbs pressure plate 18.5 - 24.4 ft lbs
what are the torque specs for lifters on a 2000 Pontiac grand am gt
Cat 3126 torque 780 ft lbs. that is for all cat 3126 c7 engines reguardless of hp rating
Torque specs for 71-73 Pontiac 400 main cap bolts 100 ft-lbs, rear mains 120 ft-lbs. Rod bolt specs 43 ft-lbs respectively.
37 ft. lbs to 120 degress
For a 1.0 litre and manual tranny it's 55 ft.lbs
refer to service manual
The main bolt torque is 100lftlbs and 120 on the rear main cap.
Torque specs for a 1996 Pontiac Grand Prix 3.1 is 185lb-ft of torque at 4,000 RPM.
remove transmission, remove torque converter (auto), or clutch and pressure plate (manual) remove flywheel flywheel and pressure plate must be Torqued to factory specs
The intake manifold torque specs for the 3.1 L on a 2001 Pontiac Grand Prix is 195 ft lb. and 264 Nm at 4,000 rpm. It also has 175 hp at 5,200 rpm.
The 1999 Pontiac cylinder head gasket bolt torque specification is 160 pounds. The intake manifold bolt torque specification is 90 pounds.
75 ft-lbs. Lock-Tite is recommended.
18 ft pounds
The torque of the 1998 Pontiac Grand Prix is 220 ft.-lbs. at 4000 rpm. This remained the standard for all sixth generation models of this car.
4cylinder 105-112 foot pounds v-6 65 foot pounds
105 ft lbs if its a 4.0. dont forget the blue thread locker.
2003 pontiac grand prix 3.1
The 1995 Pontiac sun fire cylinder had bolt torque specification is 160 pounds. The head bolts should be torqued in 40 pound intervals.
What is the head bolt torque for a 1997 chevy lumina four cylinder?