Ford
Head Gaskets and Valve Covers
Ford Fiesta
Ford Escort Diesel

What are the torque setting for a Ford Fiesta 1993 head bolts?

727374

Top Answer
User Avatar
Wiki User
Answered
2006-10-12 16:09:58
2006-10-12 16:09:58

30 Nm + 90 degree's + another 90 degree's

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


For the Chevrolet S-10 model years from 1982 to 1993, the torque for the caliper mounting bolts is 37 ft. lbs. The torque setting for the brake hose-to-caliper bolt is 32 ft. lbs.

The hub nut is 137 ft lbs......... The two lower bolts and nuts that the strut mounts to wheel assembly is 167ft lbs......... Dont over torque that hub nut you will have problems.......................

the longer (new bolts) are to torqued to 48lbs and the shorter ones are to be torqued to 45lbs then turn the bolts an additional 90 degrees the bolts need to be replaced with new one because they are streched when you torque them down

Torque is not the type of bolt but a type of wrench used to tighten bolts. A torque wrench will tell you how tight a bolt is tightened like 60lb of torque or tighten to 80lb of torque so a bolt will be tight enough to stay in but not too tight that you strip the bolt.

The spark plug torque spec range is between 6 and 10 ft/lbs.

Torque the head bolt on a 1993 Toyoto 22RE three times at 58 foot pounds of torque. The 22RE head bolts are not torque-to-yield (stretch), and are re-usable. Torque is 55-63 foot pounds. Thoroughly clean the bolts on a wire wheel and inspect for pitting, especially in the threads and replace as necessary. It is also recommended to re-torque them after about 1,000 miles. ChaCha!

For my Mercury Cougar with Aluminum Heads it is:Torque Sequence 1993 3.8 Cougar; Looking at Engine from front of car the lower bolts are 7 3 1 5 upper bolts are 8 4 2 6. Step 1; Torque in Sequence to 37 FT./ LBS Step 2;Torque in Seq. To 45 FT./LBS. Step 3; Torque in Seq. To 52 FT,/LBS. Step4; Torque in Seq. To 59 FT./LBS. Step 5; Back off all bolts in Torque Sequence 2-3 turns. Step 6; Retorque all Bolts in Sequence 11-18 FT/LBS. Step7; Rotate Long Bolts 85-105 Degrees, Short Bolts 65-85 Degrees in Sequence. Recheck final Torque in Sequence. When replacing Head Gasket be sure to replace all torque-to-yield style Head Bolts. Hope I Have Helped -u-. "Odie" OdiebuiltMC@aol.com

Fiesta Marina Cruises was created in 1993.

You did not mention if it was the intake to the cylinder head bolts (1993 buick lesabre 96 in-lbs)..... or ..... the intake upper to lower bolts ( 1993 buick 132 in -lbs) but i hope you will know wich you are looking at since there is a large difference in torqe.

Rule of thumb is 90 foot pounds on passenger cars

hi i belive them to be 115 to 125 nm, that is what the setting is in my manual

torque spec for automatic transmission pan bolts = 96 to 120 in-lbs. - Haynes Repair Manual #36071, 1993-2005 Ford Ranger and 1994-2005 Mazda B-Series Pick-ups

You have to turn them twice. The first turn is 61 psi. The second turn is 72 psi.

The 1993 Chevrolet nova 1.5 liter engine cylinder head torque settings are 120 pounds per square inch. The cylinder head bolts should be torqued at 40 pound intervals.

This is the link to Autozone DIY section. It has all the torque specs for the entire 1.9 engine and others. Copy and paste it in your browser. http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008db67

12 ft/lbs but its better to use 1/4" torque wrench set at 144 in/lb so you don't over tighten.

Torque Sequence 1993 3.8 Cougar; Looking at Engine from front of car the lower bolts are 7 3 1 5 upper bolts are 8 4 2 6. Step 1; Torque in Sequence to 37 FT./ LBS Step 2;Torque in Seq. To 45 FT./LBS. Step 3; Torque in Seq. To 52 FT,/LBS. Step4; Torque in Seq. To 59 FT./LBS. Step 5; Back off all bolts in Torque Sequence 2-3 turns. Step 6; Retorque all Bolts in Sequence 11-18 FT/LBS. Step7; Rotate Long Bolts 85-105 Degrees, Short Bolts 65-85 Degrees in Sequence. Recheck final Torque in Sequence. When replacing Head Gasket Besure To Replace all Head Bolts. Hope I Have Helped -u-. "Odie" OdiebuiltMC@aol.com

From:http://www.autozone.com/autozone/repairinfo/specifications/specificationsMain1993 Pontiac Lemans-Import 1.6L TBI SOHC 4cylApplication:Cylinder head bolt torque sequenceNote :Torque sequence ----------------| 8 4 1 5 9 || 7 3 2 6 10 |----------------Step 1: Torque in sequence 18 Ft/LbsStep 2: Torque in sequence 60 degreesStep 3: Torque in sequence an additional 60 degreesStep 4: Torque in sequence 30 degreesrecheck final torque in sequence>*** CAUTION *** Engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.-------------------------------------------------------------------------Just in case you need this info too:INTAKE [Manifold] BOLT TORQUE1993 Pontiac Lemans-Import 1.6L TBI SOHC 4cyl16 Foot pounds (Final torque) Note: to torque bolts & nuts, start in center using crisscross pattern working outward--------------------------------------------------------------------------Hope this helps. :-)

So many bolts so many torque here's a chart hope that help! http://www.fastenerman.ca/images/A_FastenerTorqueCharts.pdf You must have a pdf reader to see this chart So many bolts so many torque here's a chart hope that help! http://www.fastenerman.ca/images/A_FastenerTorqueCharts.pdf You must have a pdf reader to see this chart

Automatic transmission pan bolts torque specifications: 96 to 120 in-lbs. Haynes Repair Manual #36071, 1993-2005 Ford Ranger Pick-ups & 1994-2005 Mazda Pick-ups, B=-s Series

cylender head bolt torque for 1993 Mitsubishi expo

The lug nut torque for that 1993 Volvo 960 is 63 ft.lbs.

SOHC motor (T45 torx bit) 89 in-lbs DOHC motor (10mm bolts) 22 FT-lbs

All the torque settings for your entire car should be listed in a Chiltons manual. Get one at your local auto parts store for about 15-20 buck. darksidesteve


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.