Head Gaskets and Valve Covers
Daewoo Matiz
Toyota Land Cruiser
Timing Belts and Chains

What are the torque settings for the cylinder head bolts on a daewoo matiz?

383940

Top Answer
User Avatar
Wiki User
Answered
2007-01-20 22:04:52
2007-01-20 22:04:52

1st stage 22 lbft. 2nd stage 43lbft. 3rd stage 65lbft. 4th stage loosen 90degrees then torque to 65lbft. 5th stage run engine to hot then allow to cool for at least 4 hrs. 6th stage loosen 90degrees then torque to 65lbft


Torque for Daewoo Cielo 1.5 l engine I hope it will be the same for matiz 1. 25 nm 2. + 60 degrees 3. + 60 degrees 4. + 30 degrees 5. + 30 degrees with hot


001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


torque settings for cylinder head bolts

Get a manual on your car and it will give you the settings of the intake, exhaust bolts plus the head bolts and torque pattern.

hi i am looking for the torque settings for a proton gen 2 cylinder head bolt and crank shaft bolts both big ends and main bearing bolts

The cylinder had bolt torque specification is 90 pounds. The cylinder head bolts should be torqued in 30 pound intervals.

In four stages, 1st with a torque wrench then with an angular torque gauge. Note: when replacing the head gasket, you should replace the head bolts as well.25 n/m (18 lb/ft) + 70 degrees + 70 degrees + 50 degreesin my original daewoo manual says 25n/m +90 degrees+90 degrees+90 degrees daewoo nubira 2.0 2001

in sequence torque bolts to 20nm, then again in sequence turn a futher 120 degrees, and again in sequence 120 degrees.

torque for 2c engine cylinder head bolts

The torque settings for a 96 Fiat Punto 12cc for cylinder head bolts are 30 NM at 90 degrees. Then an additional 90 degrees.?æ?æ

torque setting for cylinder head bolts for a skoda felicia

The cylinder head bolt torque setting is 120 pounds. The cylinder head bolts should be torqued in 60 pound intervals.

The head bolt torque specs on a daewoo lanos with the 1.6 liter engine arestep 1 18ft lbs step 2 turn all bolts 70 degrees step 3 turn all bolts additional 70 degrees and step 4 turn all bolts 30 degrees that is what came straight from the torque manual

Oil bolt washers and threads lightly. stage 1: Torque all bolts to 30Nm stage 2: angle torque all bolts +90 degrees stage 3: angle torque all bolts +90 degrees

they are all torque 20nm/15lbf ft then after all angle tightened 260 degrees

100 ft Lbs when reusing the old bolts per the Isuzu manual.

40nm,60nm, 90degrees,90degrees on new head bolts

The 1993 Chevrolet nova 1.5 liter engine cylinder head torque settings are 120 pounds per square inch. The cylinder head bolts should be torqued at 40 pound intervals.

The head bolt torque settings, on your Kia 2.7 diesel engine, is 70 pounds per square inch. The bolts should be torqued at 35 pounds to begin with.

The torque specs for a Toyota Camry cylinder head is 60 pounds for the inside bolts and 50 pounds for the site bolts. The cylinder head bolts should be tight from and to end alternating.

You have not told us for what bolt or nut ?. - There will be almost a whole page of torque settings for that vehicle. Oilpan bolts may be as little as 12 while cylinder head bolts will be around 70 . We have no clue unless you name the bolt.

You have not told us for what bolt or nut ?. There will be almost a whole page of torque settings for that vehicle. Oilpan bolts may be as little as 12 while cylinder head bolts will be around 70 . We have no clue unless you name the bolt.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.