answersLogoWhite

0


Top Answer
User Avatar
Wiki User
Answered 2008-12-30 03:34:16

You can torque most intake manifolds to 35 ft/lbs (metal only, plastic ones are a different beast lol) but to get the exact torque spec buy a shop manual. TommyTrouble XXXXXXXXXXXXXXXXXXXXXXX Always start in the middle and use a crisscross pattern.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

What is bolt torque for lower intake manifold for 97 buick lesabre?

The 1997 Buick LeSabre intake manifold bolt torque specifications is 45 pounds per square inch. The manifold bolts should be torqued in 15 pound intervals.


What are Torque specs for buick century 3.1 the plenum?

Correct torque on 2000 model : 18 Ft. lbs.- upper intake manifold [ plenum ].


What is the torque for intake manifold bolts 1991 Buick le Sabre 3.8 liter?

what is the torque specificationfir the rockerarm bolt on 1991 Buick le Sabre v-6 3.8 liter


What are the torque specs for a 1993 Buick lesabre intake manifold?

You did not mention if it was the intake to the cylinder head bolts (1993 buick lesabre 96 in-lbs)..... or ..... the intake upper to lower bolts ( 1993 buick 132 in -lbs) but i hope you will know wich you are looking at since there is a large difference in torqe.


Intake torque specs 2002 Buick Century?

intake torque specs 2002 buik century


What is the torque spec for 1997 3.8 buick lesabre intake manifold?

The lower intake manifold to cylinder head torque specification is 132 inch pounds. The upper plastic intake plenum to lower intake should be done in three steps 22 inch pounds, 44 inch pounds and thirdly 89 inch pounds. Be sure to follow the appropriate tightening sequence diagram.


How do you repair a 1994 Buick Skylark intake manifold?

What's wrong with it?


How do you replace the water heater inlet pipe on the intake manifold on a 3800 buick lesabre?

replace the water heater inlet pipe on the intake manifold on a 3800


What are the torque specs for a Pontiac 3.8 intake manifold?

I'm pretty sure this is that same 3800 motor that gm uses in my mom's 2001 buick Le Sabre. Her intake was the fiberglass resin plastic and the torque specs are 89 INCH pounds. Make sure you use the right tightening sequence too. 89 inch pounds is for the upper intake or Plenum. 136 inch pounds is the torque specs for the lower intake


What is the firing order 1969 Buick Wildcat?

18436572, should be stamped on factory intake manifold


How do you get the head gasket off a 1996 buick regal?

The intake manifold, head, and exhaust manifold must be removed to gain access to the gasket.


What sensor is in the plastic intake manifold on a 1997 Buick le Sabre 3.8l?

That should be the Oxygen Sensor


What is the torque specs for a Upper intake manifold on a 1997 Buick LaSabre 3.8L motor?

Intake Manifold Upper Inch pounds newton meters Step 1 44 (5) Step 2 89 (10) Lower Step 1 27 (3) Step 2 106 (12) Step 3 133 (15) http://www.torquespecs.com/


What is the firing order for a 1969 Buick Skylark?

I think it is 18436572 usually stamped on intake manifold on the old Buicks.


Where is the egr value located on a1995 Buick Roadmaster and how hard is it to change?

on the rear of the intake manifold on the drivers side


How long will a Buick Century last?

if taken care of 250-300k, fix the manifold intake. good cars


What is the cost to replace intake manifold gasket on 1996 Buick century?

I just had the intake manifold gasket replaced on my 96 century yesterday and my bill was $450 but my gasket was only leaking out. If its leaking into your oil it may be more.


Where is the PCV valve on a 1993 Buick Regal 3.1L?

On a 1993 Buick Regal 3.1L, the PCV valve is located on the intake manifold. It is situated underneath the MAP sensor.


Where under the hood of a 2000 Buick Park Avenue is the thermometer?

The thermometer electrode is located on the intake manifold. I have found if your "idiot light" comes on while driving, the housing of the filiment might be cracked and giving a false indication. If you are looking for the thermostat, it is on the intake manifold where the the upper radiator hose meets the intake manifold. Hope this helps.


What do you do to stop a 97 Buick Skylark from leaking?

motor leaking check intake manifold really cheep gasket from the factory


Does the 1990 Buick Electra have a PCV valve and if so where is it located?

Yes, it is located in the intake manifold behind the throtle body.


Where is the PVC valve located on 1991 Buick century?

The PCV valve plugs into the rocker arms cover or intake manifold.


Where is the PVC valve on a 1991 Buick century 3300 motor?

typically ther're on the top of the valve cover or on the intake manifold.


Where is the pcv valve located on the 1997 buick park avenue?

on the left side of intake manifold under MAP sensor.


What damage can a leaky intake manifold cause in a 1995 Buick LeSabre?

Serious. On the intake manifold a leak sucking in of air will cause a lean running condition generating excessive heat if the computer is unable to adjust by adding more gas to the mixture.