answersLogoWhite

0


Top Answer
User Avatar
Wiki User
Answered 2007-03-30 15:48:41

33- Ft lbs.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

Head bolt torque specs for 2003 Chevy Malibu?

I need head bolt torque specs and sequence on 2003 Chevy Malibu 3.1


Are caliper mounting bolts reverse threaded on 2007 Chevy Impala?

No they are not.


Head torque 2.2 Chevy?

what is the torque setting for the head bolts on a 2007 chevy malibu with a 2.2L engine


What are the torque specs on a 98 Chevy Malibu V6 cylinder head bolts?

torque especifications for Malibu 1999 3.1 engine


Head bolt torque specs for a 2001 Chevy Malibu?

I need the torque and secuense for the hea d bolts for a Chevrolet Malibu 2000 3.1


What are the torque specifications for a 2002 Chevy Malibu 3.1 engine?

what is the torque specs to a 2002 Chevrolet Malibu 3.1 liter motor. Need head and intake torque specs. and sequence.


How do you torque front brake caliper mounting bolts on a 2005 Chevy Trailblazer?

Be careful. My Haynes repair manual stated a torque of 85 ft-lbs for front caliper mounting bolts for my 2005 Chevy Trailblazer. I tried to torque the bolts that much and ended up breaking the bolt off. This was a hassle to fix and you can't drive your vehicle until it's fixed with a new bolt. I had to take a vacation day to wait for the parts store to order a new bolt and have it delivered. O'Reilly Auto parts said the correct torque is 31 ft-lbs of torque. Their computer did list the same 85 ft-lbs of torque initially but said it was incorrect.


What is the head torque for a 1999 Chevy Malibu?

40lbs per square inch


Torque specs for rockers on 97 Chevy Malibu?

20 foot pounds


What is the brake caliper torque for a 1996 Chevy Silverado 1500?

55 ft. lbs.


How do you change the Rear Wheel Bearing on your 2001 Chevy Malibu?

remove brake drum or caliper, remove caliper mounting bracket if nessesary. unplug electical connecter from wheel sensor on the back side of knuckle. remove 4 hub to knuckle bolts, remove the hub and bearing assembly!!


How do you replace sun visor on Chevy Malibu?

The sun visor on a Chevy Malibu can be replaced by first removing the retaining screws and sliding it out of the mounting bracket. A new visor can then be put into place and bolted in.


What are the torque specs on a 2001 Chevy Malibu V6 engine?

For the head bolts, 37lbs


How do you remove a 1995 Chevy Corsica brake caliper?

Should be 2 mounting bolts one on top one on bottom remove these and slide caliper off rotor


What are the torque specifications when installing spark plugs on a 2002 Chevy Malibu?

11 ft/lbs


What is the oil filter torque on 2009 Chevy Malibu?

there is no torque on the oil filter!! when putting back on tighten the filter hand tight as much as you can.


What are the lug nut torque specs for a 2006 Chevy Malibu?

The lug nut torque specs on a 2006 Chevy Malibu is 100 foot pounds. Although that is the factory setting, most service tire shops will tighten to the universal specifications of 90 foot pounds.


What are torque specs for Chevy Venture front brakes?

bolt torques for front callipers slide and mounting


How do you change front brake caliper on 00 Chevy pick-up?

Remove wheel loosen and remove flexible brake line to caliper Remove 2 mounting bolts Slide caliper off rotor


How do you set torque of main bearing caps on 79 Chevy Malibu?

Need to know the engine size.


What are torque specs on front axle on 1998 Chevy Malibu?

It is 66 ft-lbs, and 46 ft-lbs for driveplate-to-torque coverter bolts.


Are torque lbs higher on rocker arms then head bolts for a Chevy Malibu?

No, head bolt torque is much higher than rocker arms.


How do replace rear disc brakes on 2004 Chevy Silverado?

Remove the caliper retaining bolts from the inside of the caliper. Lift the caliper off the mounting bracket and over the rotor. Slide the old inner and outer brake pads out of the caliper, and slide the new brake pads into the caliper.


How do you change front brakes on a 1998 Chevy Monte Carlo?

Remove the caliper bolts, caliper mounting flange, rotor. Install new rotor. Remove pads from caliper, wire brush and clean all contact surface and hardware including caliper pins. Lubricate all of them with disc caliper grease. Note how you removed everything so it goes back correctly. Torque down pins. Gently brake for first 50-100 stops.


What size specialty nut do you use to remove the caliper mounting bracket in a 93 chevy lumina?

T60. It's a torx bit.