Head Gaskets and Valve Covers
Grand Am SE
Grand Prix SE
1995-2005 Chevy Cavaliers

What are the torque specs for the head bolts on a 1998 Cavalier?

678

Top Answer
User Avatar
Wiki User
2005-10-10 03:40:16
2005-10-10 03:40:16

If its a 2.2L engine. First Pass Long bolts 46 ft. lbs Short bolts 43 ft. lbs Final Pass Tighten all bolts an additional 90 degree turn. Hope that helps

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

What do you torque the head bolts on a 1998 nissan altima 2.4 l

User Avatar

In the transmission held on by 3 bolts

User Avatar

Torque specs for a 1998 Volkswagen jetta 2.0

User Avatar

It is 66 ft-lbs, and 46 ft-lbs for driveplate-to-torque coverter bolts.

User Avatar

It depends on the brand of the rod bolts, but usually 45-50 ft/lbs.

User Avatar

What are the intake manifold torque specs on 1998 Oldsmobile bravada?"

User Avatar

What are the intake manifold torque specs for a 1998 ford f-150 xlt

User Avatar

Here are the specs for both cars and you be the judge..... 1998 Ford mustang specs: 6 cylinder 150hp 215 ft lb 1998 Chevy cavalier specs: 4 cylinder 115hp 130ft lb i say the mustang will win...

User Avatar

The 1998 Jeep Cherokee head bolt torque specifications is 120 pounds. The head bolts should be tightened by starting at one and alternating to the other end, working towards the center.

User Avatar

1998 Honda civic head bolt torque specsstep 1 14 ft/lbs step 2 36ft/lbsstep 3 49ft/lbsstep 4 retourque bolts 1 and 2 at 49ft/lbsstart with the midle bolts and do a cris cross pattern to the out side bolts

User Avatar

whats the torque spec for the pressure plate on a 1998 kia sportage?

User Avatar

"Roadwheel bolts....110Nm 81 lbf ft" per Haynes VOLVO S70, V70 &C70 1996 to 1999 Repair manual

User Avatar

NEED help is there a diagram with the bolts in the backseat of a 1998 chevy cavalier?

User Avatar

what is the torque on front wheel bearings for 1998 honda accord

User Avatar

Cylinder Head Bolts (1st Step) 68 Nร‚ยทm (50 ft. lbs.) Bolts (2nd Step) 143 Nร‚ยทm (105 ft. lbs.)

User Avatar

1.8 mazda etude 1998 con rod torque spec

User Avatar

torque specs. on lugnuts are usually around 90-100 ft.lbs.

User Avatar

get a haynes book at the auto shop its a must have for me :)

User Avatar

The torque specs for the 1998 Arctic Cat 440 engine are between 6 - 130 n-m depending on the size of the bolt and nut. The ft. per lb specs are between 4.4 and 96 depending on the bolt and nut size.

User Avatar

No, I have a 1998 Cavalier and it does not have a cabin filter. You can take off the 3 bolts off the heater blower and remove any leaves or debris.

User Avatar

30 foot-pounds of torque for each of the seven bolts

User Avatar

The bolts should be tightened in the following order. 10, 6, 2, 3, 9, 8, 5, 1, 4, 7. The torque for bolts 1 through 7 and 9 through 10 is 110 ft. pounds. Bolt 8 is 100 ft. pounds.

User Avatar

Both the front and rear bearings on a 1998 Cavalier are contained in the hub assembly. The rear hub is attached with four bolts, and the front with three.

User Avatar

Oil bolt washers and threads lightly. stage 1: Torque all bolts to 30Nm stage 2: angle torque all bolts +90 degrees stage 3: angle torque all bolts +90 degrees

User Avatar

The axle nut torque specifications for a 1998 Chevy 4x4 are 165 lb ft. The metric specs are 225 N m.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.