Best Answer

torque especifications for Malibu 1999 3.1 engine

User Avatar

Wiki User

โˆ™ 2011-09-13 21:29:49
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What are the torque specs on a 98 Chevy Malibu V6 cylinder head bolts?
Write your answer...
Related questions

Head torque 2.2 Chevy?

what is the torque setting for the head bolts on a 2007 chevy malibu with a 2.2L engine

What are the torque specs on a 2001 Chevy Malibu V6 engine?

For the head bolts, 37lbs

What are the torque specs for a 2000 Malibu Chevy cylinder head?

Tighten the bolts to 60 nM (44 ft. lbs.) in sequence. Tighten the bolts to 60 nM (44 ft. lbs.) in sequence.

Head bolt torque specs for a 2001 Chevy Malibu?

I need the torque and secuense for the hea d bolts for a Chevrolet Malibu 2000 3.1

What are the torque specs for the front caliper mounting bolts on a 1999 Chevy Malibu?

33- Ft lbs.

Are torque lbs higher on rocker arms then head bolts for a Chevy Malibu?

No, head bolt torque is much higher than rocker arms.

What are torque specs on front axle on 1998 Chevy Malibu?

It is 66 ft-lbs, and 46 ft-lbs for driveplate-to-torque coverter bolts.

What is the torque for the head bolts for a 1996 Chevy beretta 3.1 4 cylinder?

The 3.1 was a V6

How much is the torque of 2c cylinder head bolts Toyota?

torque for 2c engine cylinder head bolts

What are the torque specs for a 1996 Chevy s10 4.3 liter?

For the 1996 Chevy S-10 4.3 liter, the torque specs for the crankshaft damper bolts is 70 ft. lbs. For the cylinder head bolts, the torque is 65 ft. lbs, and for the engine mount-to-head bolts, the torque is 35 ft. lbs. For the engine mount-to-frame bolts, the torque is 52 ft. lbs.

Torque setting for cylinder head bolts for a Skoda felicia?

torque setting for cylinder head bolts for a skoda felicia

What are the torque specs for a 1990 Chevy lumina head bolts?

3.4 litre cylinder head torque is 37 ft lbs +90 degrees

Are the head bolts reusable in Chevy aveo 1.6 liter?

No the cylinder head bolts for 1.6L Chevy Aveo are TTY (Torque to Yield) bolts, meaning the bolts stretch after being torqured and cannot be reused without risk of breaking.

How do you replace a head gasket on a 1999 Chevy Malibu?

The head gasket on a 1999 Chevy Malibu is replaced by removing the coolant, intake manifold, and retaining bolts. The cylinder head can then be removed, the gasket replaced, and everything reassembled.

Should the head bolts be replaced when changing head gaskets on a 2003 Chevrolet Malibu with a 6 cylinder?

If they are torque to yield. That means if you torque it to a certain number and then have to turn it ,say, 90 degrees more. the answer is yes because you are stretching the bolts.

What are the head bolt torque specs for a 1995 Pontiac 3.1 liter head bolts?

What is the head bolt torque for a 1997 chevy lumina four cylinder?

On a 1997 Chevy Malibu 6-cylinder what do the alternator's top and bottom bolts bolt to?

I have a 99 Chev Malibu - there were 3 bolts (which is why I had a hell of a time getting it off. Persistance! I think 1 was at the back and another towards the bottom at the back.

What is Toyota Camry cylinder head bolts torque specs?

The torque specs for a Toyota Camry cylinder head is 60 pounds for the inside bolts and 50 pounds for the site bolts. The cylinder head bolts should be tight from and to end alternating.

How Rear Wheel cylinder 2000 Chevy Malibu?

remove rear wheel, remove brakes and cylinder is held on by 2 bolts from back of plate. remove bolts and brake line from cylinder !! somtimes you can take top nails holding brakes out to allow room to remove cylinder.

What are the cylinder head torque specs on 1999 Chevy venture?

The cylinder head bolt torque for a 1999 Chevy Venture is 44 ft lbs. If you have a GM special service tool # J36660A, use that to turn the bolts an additional 95 degrees.

How do you torque bolts on a 350 Chevy to specified value?

torque wrench

How do you change wheel cylinder on 2000 Chevy Malibu?

To change wheel cylinder on a 2000 Chevy Malibu, jack up the vehicle and remove the tires, brake drums and brake shoes. Spray the hydraulic line and fitting with CRC 5-56 and loosen hydraulic fitting. Remove the two mounting bolts and remove the wheel cylinder. Replace with new.

Torque settings for megane 1600 k4m?

torque settings for cylinder head bolts

What is the torque specs for head bolts on a Chevy 292 straight 6?

Torque for 292 head bolts is 95 ft lbs

What is the torque specification for Toyota Camry 1989 four cylinder head bolts?

1991 toyota camry head bolts torque specs

Study guides

Create a Study Guide