0
The basic function of power cables is to provide power to equipment. The basic function of data cables is to transfer data, from one device to another.
Wiki User
∙ 13y ago
Wiki User
∙ 13y agoThe power cables supply electricity to the computer system. The data cables are what the data travels through.
Add your answer:
Earn +20 pts
What are the basic functions of a power cable?
To provide power from a power source to some piece of equipment or tool.The basic and sole purpose of a power cable is to transport electrical energy from the source of the electricity to the device, example; Computer, Computer MonitorIt is a colored wire that connects to the motherboard in order to transfer electricity.
What are the four primary functions of hardware?
the four basic functions of the microcomputer are input, output, processing, and storage of data.
4 basic function of computer?
data processing,data storage,data movement and control.
What are the basic elements of data system?
A system, including computer system and associated personnel, that performs input, processing storage, output and control functions to accomplish a sequence on data.
What are the two basic cables found inside a computer case?
The two basic types of cables are power cables and data cables. Early PCs used a ribbon cable to connect both hard drives and floppy. Later the Hard drive cable was changed from 40 wires on 40 pin to 80 wires on 40 pins. The additional wires were grounds between each data carrier. Newer computers use a smaller serial ATA (SATA) cable that uses 7 individual wires - 4 data wires and 3 ground wires. Other data cables and connectors usually use a flat ribbon cable for connections in the case. Examples are the serial ports, parallel ports, USB ports. The early PC had few connections sold with it, and we used to use a multi-purpose card to add ports and memory capability. Since the card was overcrowded, an extra "back plane connector" was included to give you a place hook up your printer of modem. It connected with a ribbon cable and a "header" block that plugged onto pins on the multi card. The power connectors on the early PC power supply were round and a keyed header attached them to the motherboard. Newer Motherboards often have an auxiliary power connector that enhances the distribution of power to the motherboard. This is only a benefit if the computer power supply has isolated rails for the different voltage supplies, or if the board must use more current than the other wires can safely carry. Hard drives and floppy all used the same size 4 pin Molex connector. The mini power connector arrived with the smaller floppy. The new SATA drives use a special power connector. New video cards that are high performance usually include one or more power headers requiring a feed just for the video card, and possibly it's fan. Early fans for the computers piggy backed across the power connectors going to the disk drives. More modern designs have dedicated sockets on the motherboard to allow reading the fan speed or better yet, controlling the fan speed. Some mother boards allow the control of "case fans". The power and sensor wiring for these fans is a 3 conductor cable, and some use a fourth conductor as a control line.
What are the basic functions of a computer?
One of the basic functions of a computer are to input data and then process it. A computer also outputs data and stores data.
What is the function of cables?
To transport power & or data.
What are the basic parts of programming?
Data types and functions.
Can data cabling and power cabling be run on the same ladder rack?
Doing that might give you interference with your data transfer rate.
What are the two basic types of cables found inside a computer case and what are their basic?
This is a good example of a question you might get in a bad computer repair class.Never assume you know what a cable does.Always study the motherboard and see where every cable is connected. Then identify what the function of the cable is.That said. In a generic Personal Computer there are typically only two types of cables. Data and Power. Data connects the motherboard bus to your equipment (eg. HardDrive). Power cables feed power from the DC converter to your equipment.
The basic functions of many programs are?
input data, processing, output data reference:Microsoft Visual Basic 2012 Introductory
What are the basic functions of a power cable?
To provide power from a power source to some piece of equipment or tool.The basic and sole purpose of a power cable is to transport electrical energy from the source of the electricity to the device, example; Computer, Computer MonitorIt is a colored wire that connects to the motherboard in order to transfer electricity.
How do you illuminate a black blank PC screen?
Check that all cables, power and data cables are pluged in and working, verify that mains power is switched on to the monitor.
What are the four primary functions of hardware?
the four basic functions of the microcomputer are input, output, processing, and storage of data.
How data processing cycle work?
The instructions of a program generally direct the computer to perform three basic functions over and over again. These functions are input, processing and output. Collectively, these functions operate the data processing cycle.
What was the first computers functoin?
The first functions involved writing text to the screen, then adding integers, then other basic data functions were added.
4 basic function of computer?
data processing,data storage,data movement and control.
