answersLogoWhite

0


Best Answer
Copy

Check your Transmission Fluid level.

2006-09-10 14:18:50
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Your Answer

Loading...

Related Questions

How do you reset the oil change light in a 2010 Mountain Wrangler?

Key on, engine off, press the gas pedal to the floor three times.Key on, engine off, press the gas pedal to the floor three times.


How do you reset the oil change light on a 2009 dodge Dakota?

Key on, engine off. Press the gas pedal to the floor three times.Key on, engine off. Press the gas pedal to the floor three times.


How do you reset the change oil message on a 2008 jeep wrangler unlimited?

Key on, engine off, press the gas pedal to the floor three times.Key on, engine off, press the gas pedal to the floor three times.


How do you turn off the change oil display on a 2008 dodge ram 1500?

Key on, engine off. press gas pedal to the floor three times.Key on, engine off. press gas pedal to the floor three times.


How do you reset oil change light on 2008 dodge caliber?

Turn the key on, engine off, press the gas pedal to the floor three times.Turn the key on, engine off, press the gas pedal to the floor three times.


How do you reset the computer in a 2012 Dodge Journey after an oil change?

Key on, engine off. Press the gas pedal to the floor three times in ten seconds.Key on, engine off. Press the gas pedal to the floor three times in ten seconds.


My engine whines when i press on the gas pedal?

Lose some weight then....................fatty


How do you rev up your car?

start the engine and press the gas pedal while it is in park


How do you reset change oil light on 2009 Jeep Compass?

Key on engine off, press gas pedal to the floor three times, cycle key off and back on.


Why would the AC stop blowing when you press on gas pedal?

You may have a dragging pulley or clutch plate that locks up when the rpm's increase


How do you reset the oil change light on a 2011 grand caravan?

Key on, engine off. (if push button start, press button twice without touching brake) press gas pedal to the floor three times.Key on, engine off. (if push button start, press button twice without touching brake) press gas pedal to the floor three times.


How do you reset the change oil light on a 1997 Monte Carlo?

turn key halfway without starting the engine, press on the gas pedal slightly. this should work. keep tapping the gas slightly if it doesnt reset . do not press the gas pedal fully, you might flood the engine.


Why does a 2008 Chevy aveo RPM raise When you push on the brake and the car stop?

"Power brakes" uses engine vacuum to assist you as you press on the brake pedal. The diaphragm of the power brake module pulls the brake pedal harder as you press harder on the pedal. Since engine vacuum is being used, some atmospheric air is released into the intake of the engine as you press the pedal. That's all the throttle on your vehicle does to make it go faster. When more air is released into the intake of the engine (that's where the vacuum line is connected for the brakes) the engine will go faster, so when you press on the brake, it's doing the same thing. Usually people don't notice the slight RPM difference. If the change in engine RPM is extreme you MIGHT want to have the power brake module tested.


How do you reset the oil change message on a 2011 dodge ram?

Turn ignition on with engine off. Press gas pedal to the floor three times in 5 seconds. Cycle key and light should be reset.Turn ignition on with engine off. Press gas pedal to the floor three times in 5 seconds. Cycle key and light should be reset.


How do you reset the change oil light on a 2009 dodge caliber?

Turn ignition on with engine off. Press gas pedal to the floor three times in 5 seconds. Cycle key and light should be resetTurn ignition on with engine off. Press gas pedal to the floor three times in 5 seconds. Cycle key and light should be reset


What would cause a 1990 Chev lumina to flood when cold starting it?

if you press the pedal to much that is what can cause the engine to flood


When you press on the gas pedal your engine sounds like a vacuum?

The cooling fan clutch may be faulty and locked up.


How does a gas pedal work in a gasoline engine?

when you press the gas pedal the gas injection system works, its opens the air vague and flows the air to the engine, in the same time the electronic systems flows the fuel accordingly to the air flow


Why is there resistance on your gas pedal when you press it?

Occasionally the gas pedal will have some resistance when you press it. You could check and lube gas pedal, gas cable, and throttle itself.


How do you check a hydraulic brake servo?

With the engine off, press hard on the brake pedal. Turn the engine on and the pedal should depress slightly but no more than an inch or two. If your brakes either drag or stick on, or sometimes the pedal goes real hard under foot it means your servo is shot!


Do you only press the brake pedal for stopping?

No, on most newer cars you also have to press the brake pedal to shift out of Park.


A manual car has gas pedal break pedal and?

The pedal on the left is the clutch. You press it when you are changing gears.


What if the Gas pedal becomes jammed do you press hard on the gas pedal?

Slip the shift into neutral immediately, pull over when it is safe to do so, put the vehicle in park and shut the engine off.


How do you reset oil change light Jeep Compass?

Key on engine off, press gas pedal to the floor three times


How to reset oil life on a 2011 Jeep Patriot?

Key on, engine off. Press the gas pedal to the floor three times.