answersLogoWhite

0


Best Answer

Along with the head gasket you often get warping of the head. Coolant will get mixed with the oil causing engine bearing and ring damage if the car was driven after the head gasket blew. If you continue to drive the car you will eventually ruin the engine.

User Avatar

Wiki User

13y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What damage can be caused by blown head gasket?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you know if it is a blown headgaskets?

There are several possible indications of a blown head gasket: If the head gasket is blown between adjacent cylinders there will be poor or no compression in either cylinder. Poor compression in any cylinder can be caused by a blown head gasket. That condition can also be caused by a burned valve or piston. Coolant in the crank case can be caused by a blown head gasket. Compression in the coolant can be caused by a blown head gasket. An engine with a blown head gasket usually loses performance and runs poorly or not at all.


You have coolant getting into your oil how?

You have a blown head gasket or a cracked head. STOP driving this car immediately or you will do serious damage to the engine. It will need the gasket replaced and the head checked.You have a blown head gasket or a cracked head. STOP driving this car immediately or you will do serious damage to the engine. It will need the gasket replaced and the head checked.


Can a tuneup cause a blown head gasket?

No, a normal tune up cannot cause a blown head gasket. A blown head gasket normally is caused by an engine overheating or by a defect in the gasket or head. If it happened right after a tune-up that is just a coincidence.


What could be the cause of losing anti-freeze on 2002 Nissan altima?

Other than a leak, a blown head gasket. Very serious, so stop driving until this is repaired if you suspect a blown head gasket. Serious engine damage will occur.Other than a leak, a blown head gasket. Very serious, so stop driving until this is repaired if you suspect a blown head gasket. Serious engine damage will occur.


How to repair a blown head gasket?

There's only one way to repair a blown head gasket and that is to replace the gasket. You must also check to make sure that the head is not cracked or warped If it is the head will either have to be replaced or machined depending on the severity of the damage.


What causes the raditor the bubble up not the head gasket?

Overheating can cause this. Air bubbles escaping from the radiator is caused by a blown head gasket.


Why do car run hot and white smoke from exhaust?

This can be caused by a cracked head or blown head gasket.


Why would a car with a blown head gasket not start?

Because the head gasket is blown.


What damage does blown head gasket do if not repaired at once?

If not repaired at once you will get water in the oilpan. It can warp the engine head.


What would cause white smoke from a 2.4 engine A 1997 Dodge Stratus?

White smoke from the exhaust is a symptom of coolant in the combustion chamber. Normally this is caused by a blown head gasket or cracked head. Stop driving the car immediately and seek professional help, as severe engine damage will occur.White smoke from the exhaust is a symptom of coolant in the combustion chamber. Normally this is caused by a blown head gasket or cracked head. Stop driving the car immediately and seek professional help, as severe engine damage will occur.


Blown head gasket 1996 BMW 328i?

what are you asking here? PLease be more specific ...like - how do I know if my head gasket is blown, or what do I do about a blown head gasket ......


What is the difference between a cracked block and a blown head gasket?

A cracked block means that the engine itself is cracked. A blown head-gasket means that the gasket between the engine and the head has blown. Either can be caused by overheating the engine. When an engine overheats the head can warp causing the head-gasket to give out. In some engines the heat cracks the block. If the block is cracked, it's over. If the head-gasket is blown you can always machine the head surface and put it all back together.