standing in front of car looking at moter the fan clutch nut turns counterclock wise, you have to hold the belt pulley with something,they make a tool for this job,you can borrow for free at auto zone
Asked in Water Pumps
What direction does the bolt between fan clutch and water pump assembly turn on dodge truck 2007?
The fan clutch on a 2007 Dodge Ram is turned clockwise to tighten, counter clockwise to loosen. ...
How to Adjust clutch pedal height peugeot 307?
To adjust the clutch pedal height in the Peugeot 307 locate the adjuster bolt on the floor under the clutch pedal. Loosen the bolt and pull out the pedal to the proper height then tighten the bolt. To make the clutch pedal lower for the operator simply push in on the clutch pedal while the adjuster bolt is loose, then tighten the bolt. ...
What direction does the bolt turn to loosen the fan clutch on a 2003 GMC envoy?
righty tighty lefty loosey ( unless it's marked as left hand thread usually by sets of grooves in the nut or bolt head where the wrench would rest) ...
Asked in Cars & Vehicles, Toyota Camry
Which direction do you turn the crankshaft bolt for removal on a 1998 Toyota Camry?
With the bolt facing you, you should turn the bolt anti-clockwise to loosen it. It will be a right hand thread. ...
Asked in Nissan 240SX
How do you loosen drive belt on 1989 Nissan 240SX?
loosen the bolt in the center of the drive belt pulley, then loosen the bolt on the side of the pulley. as you loosen the side bolt the tension lets up ...
Asked in Toyota Camry, Volvo 740, Honda Civic DX, Pulleys
What direction do you need to turn the crank shaft bolt to loosen it and remove the pulley on a 740 Volvo 1991?
LEFT! Surprisingly the bolt is a normal right-handed thread
Asked in Cars & Vehicles, Motocross
How do you remove and replace levers on a dirt bike?
Remove the bolt in the lever perch. For a clutch lever, loosen the cable enough to remove the broken lever and replace the new one. Adjust the clutch cable back and replace the bolt in perch. For the brake (disc brake)) lever, you simply remove the bolt and replace lever, put the bolt back in the perch and you're done. If you have drum brakes, it is the same as the clutch lever routine. ...
How do you remove the fan clutch off 1999 ford expedition?
You will need a special tool which you can borrow from AutoZone. One part slips over the bolts on the water pump pulley, while the other goes over the clutch bolt. Note that some people say that they are reverse thread. Look at your fan blades. While looking at the fan and engine from the front, if the fan turns counter-clockwise, then the bolt has normal threads and you turn the bolt counter clockwise to loosen. If your fan has right...
How do you change a AC belt on 90 Acura?
You need to loosen the belt tensioner. There is a large bolt that needs to be loosened in the center of the tensioner pulley. Then the small vertical bolt is turned in the direction to loosen the belt. After the tensioner is loose replace the belt and retension it. ...
Asked in Jeep Cherokee Sport
Loosen tension on serpentine belt on a 2000 jeep Cherokee sport?
Loosen bolt in tension pulley, then loosen tension bolt. Replace belt. Tighten tension bolt. Last, tighten bolt through pulley. ...
Asked in Clutches and Flywheels, Nissan Sentra
How do you adjust a clutch on a 1994 Nissan Sentra?
there will be a cable coming out of the drivers side firewall (the dash in front of the driver) it will go to a lever on the engine just above the gear housing. the gear housing is also on the drivers side, the cable will end with a bolt and nut attached to the lever you adjust it buy taking the nut and bolt off of the lever and turning the bolt tighten for a clutch that is slipping loosen for...
Asked in Toyota Land Cruiser, DIY Projects, Pulleys
How do you loosen the idler pulley on a 1994 landcruiser?
The idler pulley is attached by a 14mm hex head bolt. Although the pulley turns counter-clockwise, suggesting that the bolt might be left-handed threads, it is in fact right-handed. A 1/2" drive ratchet with a 14mm socket will loosen the bolt if turned in a counter-clockwise direction. Be sure and loosen the belt tensioner, located below the alternator, and loosen but not remove the other alternator bolts, prior to removing the idler pulley. ...
How do you remove a fan clutch on a 1997 S10 pickup 2.2L?
The fan clutch on a 1997 S10 has a bolt on the center of the front. Remove the bolt while holding the clutch still. There is a special tool to grab the clutch fan from the rear to hold it while removing the bolt. ...
Asked in Oldsmobile LSS
How do you replace a belt tensioner pulley on a 1996 olds lss?
It has a bolt at the center of it' BE AWARE that this bolt is reversed threaded, that means the direction normally used (right, is counter clockwise) to loosen , and left is "clockwise"to tighten, therefor when removing the bolt you go in the direction of tightening to remove it, the reason for this application is that the bolt is used to releive the tension on the serpentene belt to take it off for replacement. ...
Asked in Lawn Mowers and Garden Tools, John Deere
How do you replace a PTO clutch on a john deere gt262 lawn mower?
First you must un-plug the wire that comes from the clutch to a plastic plug in and then you are ready to take the clutch off the shaft.The bolt that holds the clutch to the shaft is a coarse thread bolt and has right hand threads so you gotta hold the engine from turning as you un-thread the bolt by remembering lefty loosey and righty tighty so you will turn left to loosen this bolt and the washer is a special...
How do you loosen the tension pulley on a 95 jeep Cherokee?
loosen the pulley bolt slightly and then an upward facing bolt on the bracket will lower or raise the pulley. ...