Disconnect the negative battery cable and remove the steering wheel. Turn off windshield wiper and disconnect the wiring. Insert the key into the cognition and turn the switch to a locked position. Depress the retaining pin and remove the cylinder. Enter the old cylinder into the new ignition.
Remove the retaining ring, from the top of your 1997 Ford Astro ignition lock cylinder. Remove the wiring harness from the back of the ignition lock cylinder.
you need to push in the hole with 1/8 inch screw driver under the steering column, below your ignition switch. there is a release button in there and it just pulls out once you have that release button pushed it's actually quite easy..
Ignition Switch Box or Ignition Switch Removal & Installation 1. Disconnect the negative battery cable. 2. Remove the steering column shroud and lower the steering column. 3. Detach the ignition switch electrical hardness connector. 4. Remove 2 nuts retaining the ignition switch to the steering column housing. 5. Lift the ignition switch upward to disengage the actuator rod from the switch and remove the switch. To install: > When installing the ignition switch, both the locking mechanism at the top of the column and the switch itself must be in the LOCK position for correct adjustment. To hold the mechanical parts of the column in the LOCK position, move the shift lever into PARK (with automatic transmissions) or REVERSE (with manual transmissions), turn the key to the LOCK position, and remove the key. New replacement switches, when received, are pinned in the LOCK position by a metal shipping pin inserted in a locking hole on the side of the switch. 6. Engage the actuator rod in the ignition switch. 7. Place the ignition switch on the steering column housing and loosely install 2 retaining nuts. 8. Move the switch up or down along the column to locate the mid-position of the actuator rod lash, then tighten the retaining nuts to 47-64 inch. Lbs. (5-7 Nm). 9. Raise the steering column into position at instrument panel. Install steering column shroud. 10. Connect the negative battery cable. 11. Remove the locking pin, connect the battery cable, and verified that the engine will only crank in PARK and NEUTRAL. Also check to make certain the start circuit cannot be actuated in the DRIVE and REVERSE positions.
The knob you pull out is attached to the switch. To get the switch out, you will have to remove the panel underneath the dash, and some of the HVAC ductwork that runs underneath. Disconnect the battery. On the back of the switch, under the dash, there will be a little button you will have to push in to get the switch's shaft & knob to release from the switch. After that is done, you will be able to pull off the trim going around the face of the dash. It should just snap on. Then there will be a nut holding the switch to the dash. Remove the nut, the switch will come out the back, and then you can unplug it. Replace in reverse of these directions, only leave the swith shaft/knob for last. It will just push back into the new switch.
you dont! it has to be in the off position
Remove steering wheel Remove Steering lock plate Place ignition in on position Depress lock pin now exposed. If this is not possible, drill out lock pin.
I have to jump start my Pontiac Bonneville 1988 everyday I drive it why is that.
pull it really hard
You can replace the ignition lock cylinder in your 1994 Pontiac Firebird without removing the steering will. Remove the retaining ring at the top of the ignition cylinder. The ignition cylinder will slide out.
Begin by removing the retaining ring at the top of your 1990 Pontiac Bonneville ignition switch. The ignition switch will slide out. Remove the wiring harness from the end of the ignition switch. Reverse the process to install your new ignition switch.
To remove the "key" ignition, insert a small screwdrived in the hole directly below the ignition in the column. You will need to have the key in the ON position otherwise the ignition will not come out of the column.
Remove the retaining ring from the top of your 1997 Chevrolet 1500 ignition cylinder. Slide the ignition cylinder out and remove the wiring harness.
The 1994 Pontiac Grand Am ignition lock cylinder is held in place by the retaining ring at the top of the cylinder. Remove the retaining ring. Remove the wiring harness from the back of the cylinder.
pull trim around radio, speedometer. pull gauges radio and ac controls there is two screws .pull them. then pull electric wires to get releases cable out the key has to be in on position
you need to have the ignition barrel in the on position otherwise you cant to it.
Use the opportunity to replace the ignition. Key needs to be in On position for removal.