What do you torque the head on a 2002 Chevy cavalier 2.2 l ohv?
you torque the bolts until they are good and tight
The 2002 Cavalier 2.2 liter engine cylinder head bolt torque specification is 120 pounds. The cylinder head bolts should be torqued in 40 pound intervals.
What are the torque specs for a 1996 Chevy cavalier 2.2l engine all specs mains rods head bolts timing gear and chain line up points thanks?
What are the torque specs for a 1996 Chevy cavalier 2.2l
The 1996 Chevrolet Cavalier 2.2 liter engine had bolt torque specifications are 120 pounds. The head bolts should be torqued at 40 pound intervals.
The 2001 Chevy Cavalier 2.2 liter engine cylinder head bolt?ætorque specification is 120 pounds. The cylinder head bolts should be torqued in 40 pound intervals.
i need the head bolt torque on a 04 chevi cavallier engine 2.2 DOHC
what is the torque specs to a 2002 Chevrolet Malibu 3.1 liter motor. Need head and intake torque specs. and sequence.
1987 Chevy head bolt torque 2.5L?
They should be on the side of the cylinder head. they will have plug wires ging to them.
what is the torque setting for the head bolts on a 2007 chevy malibu with a 2.2L engine
2004 chevy aveo 1.6 head bolt torque specs
I need head bolt torque specs and sequence on 2003 Chevy Malibu 3.1
You'll have to get to the head that you want to replace by removing everything blocking where you need to get at. Then you remove all the head bolts, the gasket, clean the engine block so that it is nice and smooth, put a new gasket on, put the head on, and torque the headbolts in the correct order and correct torque specs.
65 ft lbs torque
need to know which engine you have
Torque for 292 head bolts is 95 ft lbs
the torque spec for what?
The only repair is to replace the head gasket.
torque specs 350 Chevy heads 65 lbs
What is cylinder head torque specifications for 97 Chevy lumina 3.1 v6
The 4.3 liter Chevy Astro head gasket torque specification is 160 pounds. The head gasket bolts should be torqued in 40 pound intervals.
What is the head bolt torque for a 1997 chevy lumina four cylinder?
the longer (new bolts) are to torqued to 48lbs and the shorter ones are to be torqued to 45lbs then turn the bolts an additional 90 degrees the bolts need to be replaced with new one because they are streched when you torque them down
head torque specs for 2002 honda rancher
Head torque sequence for a 2002 3800
3.4 litre cylinder head torque is 37 ft lbs +90 degrees
No, head bolt torque is much higher than rocker arms.
The 2002 Kia had bolt torque specification is 160 pounds. The head bolts should be torqued in 40 pound intervals.
The torque specifications, for your 2002 Kia cylinder head, is 120 pounds per square inch. The head bolts should be torqued in 40 pound intervals.
2003 Kia Optima 2.4, 16 valve.what are the cylinder head bolt torque specs torque at?
60-to 70 ft. lbs. of torque 60-to 70 ft. lbs. of torque
you are suppose to replace head bolts they stretch and head will not torque right. When you buy the new gasket, order new bolts.
40lbs per square inch
Blown Head Gasket or Bad Cylinder Head
Remove the head and replace the gasket. No other way to fix it.
Depends on where you live and who performs the repair. In my area on your vehicle it would cost from $400 to $600. The cost is almost all labour.
These are very important to get the torque right and the correct torquing order. Get a manual on your car at the parts store for about $18.
torque especifications for Malibu 1999 3.1 engine
on a 2002 dodge grand caravan 3.3 engine the head bolt torque specs are 65 foot pounds of torque. be sure to torque them at 10 to 20 pounds at a time and slowly work them to 65
You can buy and replace the head torque 2002 Nissan Tsuru at any garage or shop that sells the car spare parts.
For the head bolts, 37lbs
The cylinder head bolt torque for a 1999 Chevy Venture is 44 ft lbs. If you have a GM special service tool # J36660A, use that to turn the bolts an additional 95 degrees.
For the 1996 Chevy S-10 4.3 liter, the torque specs for the crankshaft damper bolts is 70 ft. lbs. For the cylinder head bolts, the torque is 65 ft. lbs, and for the engine mount-to-head bolts, the torque is 35 ft. lbs. For the engine mount-to-frame bolts, the torque is 52 ft. lbs.
check on youtube
The head bolt torque specifications, for your 2002 Pontiac Grand Prix, is 160 pounds per square inch. The head bolts should be torqued in 40 pound intervals.
Im not totally shure but i think 46ft back, and 43ft front
160 foot lbs
If it is a V8 it is 65FT.- LBS.
The year and which engine you have would help.
The 3.1 was a V6
pot head pot head