i think that it is possible that for unknown circumstances i don't know it.
number of coils, size of magnetic field strength and how quickly the magnetic field is broken with a wire.
I don't understand
V = I * R or I = ( V / R ) I = current (amps) V = Voltage R = Resistance The current in a circuit depends on the applied voltage and the resistance of the circuit.
There is no such thing as an 'induced current'. What is 'induced' is a voltage. The direction of the induced voltage is determined by the direction of the changing current that induces that voltage, because the induced voltage will always act to oppose that change in current. So, if the current is increasing, then the direction of the induced voltage will act to opposethe increase in current. If the current is decreasing, then the direction of the induced voltage will act to sustainthat current.
An induced electromotive force (emf) is an induced voltage. Voltage (emf) causes current flow, and this induced voltage will cause a current that is called the induced current.We might also add that the induced current will cause a magnetic field to expand about the current path, and this field will "sweep" the conductor. The sweeping of the conductor by that expanding magnetic field will set up an emf that will oppose the emf that was creating it.CommentTechnically, there is no such thing as an 'induced current'. It is voltage that is induced. Any current flows as a result of that induced voltage being applied to a load. But that current is certainly NOT induced!
The magnetic flux passing the coil changes by its rotation thus induced emf is produced and induced current flows
The low slip test is used to determine the D and Q axis impedance of salient pole machines. The machine terminals are short circuited, each phase voltage and current are measured. Since the terminals are short circuited, machine voltage must be reduced to prevent excessive output currents that would damage the machine.
V = I * R or I = ( V / R ) I = current (amps) V = Voltage R = Resistance The current in a circuit depends on the applied voltage and the resistance of the circuit.
In simple, number of turns of armature, intensity of magnet and speed of machine are major factor affecting induced emf in dc generator. If speed is increased, voltage will be increased simultaneously. Also Voltage is greater if number of turns are increased. Electro-magnet in the poles of a DC Generator also play an important role in the induced EMF. If intensity of magnet is exceeds, voltage also increased as well.
The induced voltage acts to oppose any change in current that is causing it. So, if the current is increasing, then the induced voltage will act in the opposite direction to the supply voltage; if the current is decreasing, then the induced voltage will act in the same direction as the supply voltage.
You can vary the induced voltage by varing the speed of the rotor.
There is no such thing as an 'induced current'. What is 'induced' is a voltage. The direction of the induced voltage is determined by the direction of the changing current that induces that voltage, because the induced voltage will always act to oppose that change in current. So, if the current is increasing, then the direction of the induced voltage will act to opposethe increase in current. If the current is decreasing, then the direction of the induced voltage will act to sustainthat current.
There is no such thing as an 'induced current'. What is 'induced' is a voltage. If the conductor into which that voltage is induced forms a complete circuit, then a current will result. But it's the voltage that's induced, NOT the current! The direction of the induced voltage is explained by Lenz's Law which, in simple terms, tells us that the direction of the inducted voltage is always such that it will oppose the change in current that causes it. So the induced voltage will oppose any increase in current, but will act in the same direction as a reduction in current.
Induced voltage is alsocalled ghost or phantom voltage as if you apply a load it vanishes. induced voltage will be potential/electrical pressure. Amperage is the actual flow of current being used, Watts being its calibration of total power used.
An induced electromotive force (emf) is an induced voltage. Voltage (emf) causes current flow, and this induced voltage will cause a current that is called the induced current.We might also add that the induced current will cause a magnetic field to expand about the current path, and this field will "sweep" the conductor. The sweeping of the conductor by that expanding magnetic field will set up an emf that will oppose the emf that was creating it.CommentTechnically, there is no such thing as an 'induced current'. It is voltage that is induced. Any current flows as a result of that induced voltage being applied to a load. But that current is certainly NOT induced!
A: impressed voltage is a mechanical connection involved induced has no mechanical connection except for proximity
According to Faraday's law, a voltage is induced in a conductor by a changing magnetic field.
There is no such thing as an 'induced current'. Voltages are induced, not currents. If a voltage is self-induced into a coil, then that voltage will oppose any change in current. If a voltage is mutually-induced into a separate coil, no current will flow unless that coil is connected to a load.
as speed increases, induced voltage increases