answersLogoWhite

0

  • Car Starting Problems
  • Starters and Ignition Systems
  • Ford Taurus

What if you do not have the old key to turn to the on position for installing the new ignition in a 94 Ford Taurus?

User Avatar

Wiki User

βˆ™ 2007-08-20 21:03:59

Best Answer
Copy

My Ford truck key fits and starts my taurus! But that might be because the switch is worn, but you might want to try a couple different ford keys before tearing off the steering column. there were answers for hard way also, here is one way that might work although it doesnt sound very easy to me: http://www.ford-forums.com/ford-taurus/4345-how-replace-ignition-switch.html

2007-08-20 21:03:59
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Add your answer:

Earn +5 pts
Q: What if you do not have the old key to turn to the on position for installing the new ignition in a 94 Ford Taurus?
Write your answer...
Submit

Related Questions

Where is the ignition module on a 1993 Ford Taurus located?

The 1993 Ford Taurus ignition module is located behind the dashboard. The ignition module, can be found on the drivers side of the dashboard.


What is the relearn procedure for a Ford Taurus?

Change ignition.


How do you remove an ignition switch on a 1996 Ford Taurus GL?

I have a 96 Ford Taurus and need to get the key switch out. Please help.


In a 97 Ford Taurus if you lift hood to disable alarm will the ignition shutdown and lockout automatically?

in a 1997 Ford Taurus if you lift hood to disable alarm will the ignition shutdown and lockout automatically?


Does a 2003 Ford Taurus' ignition key have a chip?

yes


Is there a TPS sensor on a 2004 Ford Taurus SES?

yes there is 2004 Ford Taurus Throttle Position Sensor - Partstrain.com


How much is a ignition switch for a 2000 Ford Taurus?

The price for an ignition switch for a 2000 Ford Taurus is around $60.00. Installation for an ignition switch will typically take between 60-90 minutes. Labor costs will run around $100.00 for installation.


Where is the camshaft position sensor located on a 1998 ford taurus 6 cylander dohc?

The camshaft position sensor is located beneath the wheel on a 1998 Ford Taurus 6 cylander Dohc.


Where is distributor on 1998 Taurus?

A 1998 Ford Taurus uses the Electronic Distributorless Ignition System ( EDIS ) with a coil pack , so there is no distributor


How often you change the ignition coil for a 2002 Ford Taurus?

Every time it becomes defective.


Can a 1996 Ford Taurus replacement ignition lock cylinder be fitted to the original key?

Yes it can


How do you reset the throttle position sensor?

how do you reset the throttle position sensor on a Ford Taurus 3.8 1992


Ford Taurus ignition switch removal?

Ignition switch is located at the bottom of the steering column. Remove the lower trim panel and you can see it.


Where is the crank position sensor located on a 1999 Ford Taurus?

Under the hood


Where can you find a diagram of a 1996 Ford Taurus ignition module?

CAR GUYS.COM OR YOU CAN GO TO YOUR LOCAL LIBRARY


How do you change ignition on 93 Ford Taurus?

Ignition what?CoilControl moduleSwitchLock cylinderSee "Related Questions" below for more


What could prevent a Ford Taurus from starting if a new ignition switch has been installed?

My Taurus won't start if the steering wheel isn't perfectly straight.


How many coil packs are there in a ford 2000 Ford Taurus 3.0 24 DOHC?

In a 2000 Ford Taurus , the 3.0 liter " Duratec " DOHC - V6 has the Coil On Plug ( C.O.P. ) ignition system . So there are ( 6 coil packs )


How do you remove the ignition lock cylinder from a 1996 Ford Thunderbird?

Disconnect batter ground cable. Remove the upper and lower steering column shrouds. Remove lock screw and disconnect ignition switch electrical connector. Rotate the ignition switch to the RUN position. Remove the two screws retaining ignition switch. Disengage ignition switch from the actuator. When installing new key set, ensure new key set is in the RUN position prior to installion.


Where is the ignition coil in a 2002 Taurus SEL with dohc 24 valve V 6?

The 2002 Ford Taurus V-6 engine ignition coil can be found on the firewall in the engine compartment. The coil is located on the drivers side of the firewall.


Can you put a 1999 Ford Taurus Sho Engine in a 2007 Ford Taurus?

Yes, a 1999 Ford Taurus Sho Engine will fit in a 2007 Ford Taurus.


How do you get wipers on Ford Taurus wagon to return to regular position They are stuck in up position when turned off.?

replace the wiper motor


Why Loud click from Ford Fiesta on turninng ignition key to position 1?

Probably teeth in ignition column binding


How do you change egr266 valve in 1997 ford tauras?

wiper motor does not go to home position on a 19954 ford taurus sho


When was Ford Taurus created?

Ford Taurus was created in 1986.