What is a good glue to use to glue aluminum to foam?
Silicone works well.
An epoxy would be good.
Yes, I believe so. You can use wood glue on foam.
High density polyethylene foam. Use heat. Non foam plastic use super glue.
You can find the type of glue you need at the upholstery shop. They will be able to advise you on how to make the repair you need. It will probably be a good idea to use both a foam glue, and some upholstery tape to hold it together.
Use a construction adhesive like PL300
of course you can ! ANS 2 - I don't know what 'fun foam' is - but I DO know that hot glue melts many foam surfaces.
Use a spray contact cement if the foam is flexible , or PL300 if it's rigid foam board.
Clearco 444 is safe to use on EVA foam. -Get it at foam and upholstery stores and possibly stores like Michaels.
On hard styrofoam you can use PL 300, on soft craft foam use Clearco 444
yes it will most likely ANS 2 -Hot glue will also melt many kinds of foam. -Much better to use Clearco 444 (from craft stores,) or PL300 from hardware stores.
Silicone or PL300.
There are a few good ways to do this. You can use Clearco 444, which is in a spreader tube, PL300 which is in a caulk gun form, or a spray contact cement such as Elmer's.
R5 Epoxy is not for concrete, it's a marine glue for use on aluminum and plastic parts.
Gorilla glue ANS 2 - Epoxy will work and silicone will work.
Use super ultra mega glue. Or use a construction adhesive called PL300. It comes in a squeeze-tube and a caulk tube.
J B Weld is excellent for aluminium.
Use a spray adhesive like the new one from Elmer's. -Available in Walmart.
White glue, , yellow carpenter's or wood glue, polyurethane (Gorilla) glue, and epoxy all work with styrofoam. Foam safe or odorless cyanoacrylate (CA) glue also works. Do not use regular CA or super glue. It will melt the foam. BTW, the other answerer is correct that the glue joint will likely be stronger than the material itself. This is no reason not to go ahead and glue it anyway. ANS 3 - I've stuck many… Read More
Try gasoline or acitone but there is no guarentee. ANSWER: A couple of different ways. I use sandpaper to remove glue off of wood. I use a wet cloth to get it off before it dries. On aluminum, use a paint scraper or putty knife. ANS 3 - It depends on the type of glue - you haven't said which. -Aluminum is no problem, almost any glue will be removed with careful use of a… Read More
Contact cement. ANS 2 Contact cement will melt some foam surfaces ! - Use PL 300 in caulk tubes for best results
glue it together and then use a blowtorch
TiteBond 2 will do the quite well, PL300 works also, but is thicker.
Experiments are used to solve research problems. Let me give you an example. Let us say, you want to attach some foam to concrete but you don't know the best way to do it. You might buy six different kinds of glue, and use each kind of glue to attach some foam to concrete, carefully marking each piece of foam so that you will know what kind of glue was used for that piece. After… Read More
Yellow glue is good, white glue is OK.
Hot glue and super glue are for different uses. Both are good within their use.
A good glue you can use for soft plastic which is a flexible material is Gorilla Glue.
regular glue is good for paper and wood glue is good for wood. if your using it for something more related to wood then use that one. if your using it for something more related to regular the use that.
Just use standard wood glue or PVA
You don't actually use the orange peel as glue. You use the orange peel, which is acid, to melt polystyrene, which is sticky and a good source for glue.
Various industrial glues will do this. I have tried a few and find PL 200 to be the best and most economical.
PVA (polyvinyl acetate) is a good glue for wood and paper.
Good quality crazy glue.
Don't use Gorilla glue, you can make things worth. I had very good experience with www.denturerepairlab.com ANS 2 NO , you should not use gorilla glue on dentures.
You can staple it or use tape. use super glue or use super glue and microave it for 30 sec good as new
White glue is good for that.
A construction glue called PL300 is formulated specially to hang panelling and foam board. PL300 is most convenient in caulk tube form, to use in a caulking gun.
Aluminum foil is pretty good and white paint will help reflect the heat from the sun. Use fiber glass and then cover it. Use duct tape and bubble wrap. Heat can't transfer through. Use duct tape, aluminum foil and a see through container. Using a rubber material or reflectors would slow down the process of cooling the liquid. Another thing to use is foam peanuts and paint both containers with black/dark paint. Use a lot… Read More
use Liquid Nails when installing foam to the walls or cieling. I always like to spread adhesive on both the foam and the wall and let it set for about 10 -15 minutes before mating the two together for the permanent bond.
yes, but once the hot glue is on good luck getting it off.
Yes, but it would be better to use Elmer's new spray contact cement. -In Walmart now.
Fixing a cracked aluminum bat is not a good idea, because of safety. There are many ways to patch the crack, but never restore the integrity of the bat. You can use aluminum patch (comes in a tube, like glue). That will fill the crack and make the bat appear like new, but it will never have the same characteristics. I saw a patched aluminum shatter once -- it was not a pleasant experience for… Read More
3M makes an adhesive spray that can stick it back in place. The problem is that the headliner is sagging because the foam between the fabric and the cloth is usually crumbling. If it is, it is useless to glue to it because it will not have a good surface to adhere to. To do it up properly, pop out the headliner and peel the cloth off, scrape the panel clean of foam, launder the… Read More
Use a good mastic.
Yes, but it won't be as good
Use a good epoxy .
Aluminum only needs to be added to other aluminum and melted and it is ready for use in a number of products.
Use Styrofoam to build the model of the Biltmore Estates for a school project. Use pictures of the estate to get the basic form. Hold the foam pieces together with glue or broken pieces of toothpick. Build the mansion on a foam base. After the entire model is constructed, paint and add embellishments.
get foam/ card board. cut it into the right pieces. glue/ tape them together into the right places. P.S. You MIGHT want to use some metal string.
www.kckpl.lib.ks.us/YS/CRAFTS/sock.HTM This site shows how to use a regular sock, glue, string and colored foam to make a chicken hand puppet.
You should not use regular PVC glue at lower temp than about 40f. -The glue is too thick and will not make good bonds this cold. -Weld On 725 is recommended for lower temperatures.