0
A mechanic is someone who works or repairs mechanical systems. It could be cars or trucks. It could also be a hydraulic system in a large factory.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How to fix 2000 intrigue head gasket water leak repair?
Take it to a mechenic asap....lady%preach
Does a Mitsubishi magna 92 model 4 cylinder manuel have a starter motor if yes where is it located?
i dont mean to be rude mate but if your asking if a car has a starter motor take it to a mechenic
How much should you expect to pay for a clutch replacement in a 98' ford escort zx2?
You can find a Stage 2 or 3 clutch on eBay for about the same price as you could buy and OME clutch at your local autoparts store. About 150 for the clutch, and 100 to 300 for installation (depending on the mechenic). -Antwon00
What does the light shaped like an engine mean on a ford f 250 diesel truck?
Well you can go down to advanced or auto zone the will ron a digonistic (OBD1)on it if its 96 or newer if its older you can take it to your avrage mechenic and they can run the obd1 test on it and it will give you a general idea of what it could be and reset all the codes
Will an auto reset circuit breaker work in your trucks fuse box If so you would you need a 12v 20A breaker for your 20 amp fuseThe fuses keep blowing on your S-10 seconds after you put them in?
Why don't you go to a mechenic shop and have them fix the problem.The risk is if you put a bigger fuse or same fuse and keep blowing sooner or later you will blow some more expensive component, there is also the chance that could lead to a fire on the electrical system, and trust me sparks and gas they don't go along very well.
Whats the difference between an auto technician and mechenic?
Its the same thing. Only that now trained mechanics are called Auto Technicians due to the fact that now you will need a good solid 2 year eduction to work on the ever changing and advancing automobile.
Who dies in final destination 4?
these deaths are in order: the racics guy, died in truck expolosion. the two boys mom, rock shot at her and struck her eye. Andy the mechenic,gas tank lifted him up and he hit the fence making 1/4 of his body come off. hunt, inards suck out his butt in pool! cowboy, bath tub fell from 2nd floor of hospital and crushed him. the guard, hit by of bus! these deaths are in nicks vision. Janet movie theature screen exploded and a bar pierced her chest. laurie, got crushed in ecelator. nick,laurie,Janet, truck bursted into coffe shop and hit them. lauries head came off, Janet gets crushed under tire, and finally, nick head hits the blood spurts out and his teeth come out.
What causes a Saturn SL1 to continue to make clicking and clunking noises when you turn and when you brake after the CV axles have been replaced?
Check the strut assembly on the side that is making the noise. It is possible that the strut is starting to go and that's what is making the noise. This may especially be true if you can make the clunking sound happen by pulsing the brakes as the car is moving forward. I just went through a similar problem with a 1997 SL2. The car had only 78,000 original miles when I had new brake calipers and brake lines installed (by a friend) and shortly afterward the car developed a "clunking" noise during hard right turns. We, the friend and I, checked damn near everything and though I felt it had to be related to the brake work the friend, who is a much more experienced mechenic felt otherwise. We installed new axle assemblies on both sides to no avail and I decided to allow the problem to get worse to mak locating it simpler. Finally, after about six months of use the problem got severe enough that I was becoming concerned. The noise started appearing even while braking with the wheels straight. I finally took the car to a Saturn dealer and they located a brake line that had been installed incorrectly and was rubbing on the rotating wheel assembly during certain manuvers, including turning and sometimes when braking. The brake line was worn almost completely through and was on the verge of breaking and replacing the line eliminated the problem. So much for my friends expertise!!
