clipper is an AC application of diode. The Clipper clipps off a portion of the input signal waveform without distorting the remaining part of the alternating waveform. We can use different type of alternating waveforms as input such as sinusoidal, Triangular, square etc. There are different types of clippers e.g. series clipper, parallel clipper etc. but the method for solving all the type of circuits are same. So there is no need to remember the procedure for one particular clipper circuit. There are different types of clippers e.g. series clipper, parallel clipper etc. but the method for solving all the type of circuits are same. Now let us discuss the procedure with the help of a problem. Suppose we have given a clipper circuit shown below: Because clipper is an AC application of diode. So we apply an AC signal at the input Vi. Our aim is to find out the waveform of Vo. The solution steps are: Step 1 : First of all analyze the circuit by bifurcating the input waveform in positive half cycle and negative half cycle.
Step 1.1 : Positive half cycle : Positive half cycle is equivalent to a battery of positive polarity and variable potential.
Step 1.2 : Negative half cycle : Negative half cycle is equivalent to a battery of negative polarity and variable potential. Step 2 : Now analyze the circuit with positive half cycle.
The next step is to check the condition of diode i.e., whether the diode is forward bias or reverse bias.
In the circuit shown above it is clear that the diode is forward bias and hence equivalent to short circuit (because it is ideal diode).
Now analyze the variation of Vo.
It is clear that And because Vi varies sinusoidally, so Vo also varies sinusoidally. Step 3 : Now analyze the circuit with negative half cycle The next step is to check the condition of diode i.e., whether the diode is forward bias or reverse bias.
In the circuit shown above it is clear that the diode is reverse bias and hence equivalent to open circuit (because it is ideal diode).
Now analyze the variation of Vo.
It is clear that Step 4: Now combine these two waveform.
main difference is that clamper circuit contains a caoacitor while clipper not clipper cut off the specific portion of wave
monolithic integrated circuit
A fuse is designed to 'blow' if the incoming current exceeds its rating. A rectifier circuit will 'clean up' spikes in the mains supply.
A Printed Circuit Board (PCB) is the skeleton of most electronic devices. It provides not only a solid physical base for the components to be mounted upon, but also the electrical interconnects (traces) between the components.
In terms of power I2C stands for an "Inter-Integrated Circuit". An I2C is used to connect slow speed computer components to the motherboard or other electronic devices.
You can Find All Answers Of Complete Numericals here :http://electronic-devices-and-circuit-theory.blogspot.comDont Forget to thank me ... :p
Circuit components are the small devices used in electronic circuits to obtain the desired response.
main difference is that clamper circuit contains a caoacitor while clipper not clipper cut off the specific portion of wave
A clipper circuit will not let a voltage rise above a certain value, perhaps set with a zener diode. A sine wave that is clipped will have a flat top as seen on an oscilloscope. Older transistor audio amplifiers clipped music waveforms giving an unpleasant distorted sound due to the output being clipped at the power supply rail, which was a fairly low voltage before high-voltage transistors were developed.
A cicuit board is a board made of plastic and metal interconnections where the various electronic devices are assembled in discrete form to make up the circuit.In an integrated circuit a semiconductor chip is so processed such that the various electronic devices and components are directly grown on it.
applications of clipper circuit
These would include triggering devices or the Schmitt trigger. They help to control another electronic circuit from the one that you are using.
how can i get 2203: electronic device and circuit question bank in B.E.-E.E.E. 2nd for Anna university chennai
monolithic integrated circuit
clipper circuit is used to remove some part of wave form(positive part,negative part or peak)... clamper circuit is used to shift the wave form (up or down) ....
Electronic devices.
These would include triggering devices or the Schmitt trigger. They help to control another electronic circuit from the one that you are using.