Best Answer

the normal oil pressure should equal to at leasr 10 pounds per 1000 rpm's

my 1992 runs abt. 40-50 Psi while cruising. It will go up and down as RPMs increase or decrease

User Avatar

Wiki User

โˆ™ 2011-09-14 12:57:01
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What is normal oil pressure for a 1992 4.3L S-10 Chevy Blazer?
Write your answer...
Related questions

Where is the oil pressure sensor on a 1992 S-10 Chevy Blazer?

it is behind the destribuater at the firewall

Is there a fuel pump reset switch for a 1992 Chevy blazer s 10?

No. A Chevy Blazer does not have a reset switch.

Will a 1992 Chevy s10 transmission fit in a 1984 Chevy 4x4 blazer?

Not unless the 1992 is 4x4.

Where is the ECM located in a 1992 Chevy S10 blazer?

The ECM on a 1992 S10 Blazer is located below the glove box.

Installing fan belt on 1992 Chevy k1 blazer?

Put your new fan belt around the pulleys of your 1992 Chevy Blazer. Tighten the fan belt with the tensioner pulley.

What is code 43 1992 Chevy S10 blazer?

knock sensor

Where is fuel pump in a 1992 Chevy Blazer?

Inside the fuel tank.

What is the max number of miles for a 1992 Chevy blazer?

Mine has 320,000

Why is my brake light on in a 1992 Chevy Blazer?

you most likely need to change them

Where is the solenoid on 1992 Chevy s10 blazer?

The starter solenoid is attached to the starter.

Where is the fuel pump at on a 1992 Chevy k5 blazer located?

In the fuel tank.

I need a Wiring diagram for 1992 Chevy blazer from distributor to plugs?

haynes or chiltons will have this

How do you replace the magnet under the distributor on a 1992 Chevy blazer?

buy a new distributor

Where is the fusebox on a 1992 Chevy Blazer?

Under the Dashboard on the Drivers side, has a Plastic Cover.

If a 1957 Chevy pickup truck body be placed on a 1992 Chevy s-10 blazer?

Not without fabrication.

How much will it cost to repair a transmission on a 1995 Chevy Blazer S10?

I live in DE and they wanted 12 to 15 hundred to do my 1992 blazer.

When the temperature gauge gets to normal on 1992 Chevy S10 Blazer it shuts off What could be causing this problem?

change your ECT sensor. It tells your vehicle if it is too hot to operate.

Where is the proportioning valve on a 1992 Chevy blazer s10 4x4 located?

under the master cylinder.

Where do you add air conditioning refridgerant on a 1992 Chevy blazer?

Into the low side service port.

1992 blazer with code 63?

low pressure on you MAP sensor clean it or replace it

Where is the fuel pump on 1992 Chevy blazer s10 Tahoe 4x4?

its in the gas have to drop the tank to get to it!!!

How do you adjust the idle on 1992 Chevy s10 blazer?

You don't, it is done by the ECM (Engine Control Module).

1992 Chevy s-10 blazer stuck in park?

should i push it off a cliff

How do you change front wheel stud on Chevy 1992 s10 blazer?

The front wheel stud on a 1992 Chevy Blazer S10 can be changed by jacking the vehicle up, removing the wheel, and unbolting the caliper. The rotor assembly can then be removed, and the wheel stud pressed or hammered out of its seat.

Where is the computer located in a 1992 Chevy blazer?

Behind the passenger side kick panel or behind the glove compartment.