Head Gaskets and Valve Covers
Chevy Blazer S-10
Honda CRX
Honda Civic LX

What is the correct 1991 Crx head torque specification and sequence?

404142

Top Answer
User Avatar
Wiki User
2006-04-07 18:59:42
2006-04-07 18:59:42

hondahookup.com has manuals u can download with the info u need

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

hondahookup has manual you can download

User Avatar

what is the head torque sequence for a 1991 pathfinder

User Avatar

There is no torque sequence just torque rocker arm studs to the proper torque

User Avatar

The 1991 Buick 3.1 liter rod cap torque specification is 90 pounds. The rod bolts should be torqued in 45 pound intervals.

User Avatar

The cylinder head bolt torque specification is 90 pounds. The cylinder head bolts should be torqued in 30 pound intervals.

User Avatar

The torque specs and pattern on the head bolts of a 1991 Toyota pickup with a 3.0 engine are 5, 4, 6, 3, 2, 7, 1, and 8. This sequence is started from the center of the head and requires 75 foot pounds of torque on each bolt.

User Avatar

does a 1991 thunderbird torque converter have a drain plug

User Avatar

The 1991 GMC Sonoma 2.8 liter crank sequence should begin at the front of the crank alternating to the rear. Keep alternating back and forth until you reached the center.

User Avatar

If you are asking because of your valve cover leaking oil, there was a recall on that year valve cover gasket.

User Avatar

Need more info. Torque specs. for what?

User Avatar

What is the torque of 1991 ford escort piston rods

User Avatar

what is the torque on the bolts for the transmission pan on a 1991 ford thunderbird 3.8

User Avatar

60-to 70 ft. lbs. of torque 60-to 70 ft. lbs. of torque

User Avatar

what is the over all torque for a Mercedes 300e 1991

User Avatar

what is the torque specificationfir the rockerarm bolt on 1991 Buick le Sabre v-6 3.8 liter

User Avatar

225 horsepower at 4200 RPM and 300 lb/ft torque at 3200 RPM

User Avatar

Purchase a Haynes or Chilton's repair manual at any auto parts store. Here you will find all the valve and torque specs.

User Avatar

theyre pre gapped otherwise it depends on engine specification

User Avatar

The correct factory tire size for a 1991 Jeep Wrangler is 235/75 R 15.

User Avatar

Camshaft carrier/cylinder head mounting bolts to 25n.m (18 lb ft.) in figure 21 each bolt an additional 60 degrees each bolt to 120 degrees (additional 60 degrees) each bolt to 150 degrees (additional 30 degrees) bolt sequence as follows; passenger fender 8 4 1 5 9 drivers fender 7 3 2 6 10

User Avatar

Honda Accord 1977-1993 1.8Ltr Engine code F18A2 2.0Ltr Engine codes F20A2 F20A2/3/6 F20A4 F20A5F20A8 2.2Ltr Engine code F22A3 All torque figures are listed as stage 1. 40 newton metres stage 2. 70 newton metres stage 3. 108 newton metres Tightening sequence is 8 5 2 4 10 9 3 1 5 7 Bolts 8 & 9 are nearest to the flywheel side of the engine hope this helps


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.