What is the electric consumption of 200 amp 220 Volts welding machine at full load?
Westinghouse Electric and mfg co 110 volts style 281650
500 volts up to 1000 volts electric eel have
60 volts for stud welding
The actual welding current may be greater than can be supplied from you electric panel. Therefore, the primary side of the welder may be supplied with 240 Volts at 30 Amps as an example or 7200 watts. In the welder if this was transformed to 120 volts at 60 Amps you would have more current and less voltage but essentially the same wattage with some losses. Therefore, you have transformed the current capacity at the… Read More
This can not be done. A single phase supply of 230 volts can be used from a 415 volt three phase wye system but not the other way around
Electric eels can produce up to 600 volts of electricity.
Gas stove use 120 volts at 200 watts of power when oven is running Electric stove need 220 volts at about 20 to 50 amps Electric dryer needs 330 volts at about 30 amps
No. The machine must be used on the nameplate rated voltage.
The volt is the derived unit for electric potential, electric potential difference, and electromotive force.unit of volts is V.
You are going to need an adapter that will change 240 volts to 120 volts. The wattage of your machine at 120 volts is, 120 volts x 2.5 amps = 300 watts. The capacity of the adapter will need to be in the 500 watt range. The machine will operate a bit slower at 50 Hz.
The electric eel can produce a powerful electric charge of up to 600 volts. The eel uses this electric shock for both hunting and as a means of self defense.
Why 250 volts AC in New Zealand instead of 110 volts AC which America uses is one safer and is more energy footprint required to produce the higher voltage?
The reason for increasing the voltage in the electric network is, in fact, that it saves energy. The power dissipated in electric wiring is proportional to the square of the electric current. By increasing the voltage, the current decreases provided that the power consumption at the consumer is to remain constant. This means less loss in the electric network. For the same reason, very high voltages, hundreds of thousand volts, are used in long-distance wires… Read More
Volts are a measure of electric potential difference.
240 Volts AC.
answer is 240 volts.
Generally, no. Some welding machines are designed to run on 110 volts and they are able to weld using limited power. However, a welding machine that is design to run on 220 volts requires more power than can safely be provided by a typical 110 outlet (even if a converter is used). Here's why: 110 Outlets typically only have #12 (or even #14) gauge wire, which can only support so much power before becoming dangerously… Read More
Electric Iron by far.
any type of electric used for heat is expensive. but heating the home is cheaper in the long run because it use's 220 volts of electric heat. were as a fireplace would use 115 volts. which draws more amps then running on 220 volts
Voltage is what is measured in volts. This is the electric potential difference between two places. The electric current is also measured so as to ascertain the voltage.
Electric eels can shock any animal that gets near it, and its volts can produce 600 volts that are strong enough to kill a human.
Welding leads, or cables, are mainly used as a secondary connection used where the power supply doesn't exceed 600 volts. For more information, one can visit aerolexcables.
About 400 volts to 650 volts. Depends on the size of them as well.
Up to 600 volts depending on the size of the eel.
No, although both electric eels and catfish are ray-finned fishes, electric eels are the only members of the genus Electrophorus. There are electric catfish, but they are not closely related to electric eels and their electric shock only reaches an intensity of 35o volts versus the electric eels' intensity of 6oo volts.
Answer depends on voltage being used. Volts x amps = watts 1000 watts = 1Kw You have 200 amp welder. Assuming you have 240volt power line to welder: 240Volts x 200amps = 4800 watts = 4.8Kw
electrocution is electric curent
An average sized electric eel (Electrophorous electricus) can discharge 450 volts at about 1 ampere. Dicharges of 650 volts have been recorded.
The electric potential difference is measured in volts. The amount of volts will depend on what kind of plates and the solution which the plates have been put in to.
Electrical potential is measured in Volts. Electrical potential is measured in Volts.
In your home your stove and electric clothes dryer usually run on 240 volts AC. These appliances require a three wire to feed them as they both need 120 volts for their controls.
Is it possible to convert 110 volts electric motor to 220 volts so that i can connect it directly to a 220 volts outlet?
no it is not possible. mark tahiliani
If an electric eel produces 500 volts of electricity how many watts is that... if you need amperes to get the answer how do you find that out?
158.11388300841898 volts WRONG According to: "Electric Fish." Encyclopedia Americana. the answer is: "The electric eel (Electrophorous electricus) can produce a discharge of over 500 volts (at about one ampere) and the fresh water African catfish (Malapterurus electricus) produces about 350 volts." Also: Guinness Book of Records. New York: Bantam, 1992: 95. It states: "The most powerful electric fish is the electric eel, which is found in the rivers of Brazil, Columbia, Venezuela, and Peru. An… Read More
No. In North America you are billed on the consumption of watts (amps x volts). Both legs L1 and L2 are monitored inside the watt-meter that is situated on the side of your house and are independent from the unbalanced or balanced load on the neutral.
It is probably not rated to run at six volts. Check the labelling.
Increase the electric volts
The power in an electric circuit is volts x amps, so you need both volts and current to calculate watts.
Electric eels can send 600 volts to the shark and can possibly kill it.
Watts = Volts x Amps, so the answer is 3120.
AC, 120 Volts.
In the U.S. the most common residential voltage for an electric clothes dryer is 240 volts. In commercial application you will find clothes dryers that operate at 208 volts. In UK 240V.
The energy consumption for the same appliance the power consumption in watts would be the same watts = volts X amps. In general if an appliance requires 10 Amps @ 110V then it would only require 5 amps @ 220V In general in an a North American house the appliances that run on 220V are on 220 because they would pull too much power to be logically wired on 110V. So they do pull more… Read More
An electric eel has killed a caiman with its volts, but it also died from the caiman's bite.
the electric chair because its volts are 750vlts
Volts are in SI electric potential difference, electromotive force voltVW/Am2·kg·s-3·A-1
If you are in North America, your stove and dryer run on 240 volts.
In different electric and electronic devices, voltages are used in the range of perhaps 0.5 volts to 5 million volts. So the average is somewhere in the neighborhood of 2,500,000.25 volts.
Some where on the electric piano there will be a manufactures label. When you find it the voltage and amperage will be stated. To find the wattage use the formula W = Amps x Volts.