It is what the carburetor or fuel injection is mounted to.Plain and simple.Or under the air cleaner assembly.
The Mazda B2200 truck body did not change much, if at all between 1986 and 1993. There should be no differences in the shape of the engine compartment. -Kyrasis6 Owner of Mazdatruckin.com
The firing order on all 86-93 Mazda B2200s is 1-3-4-2 when facing the distributor from the driver side it turns clockwise. The terminal facing the front of the truck on the distributor cap is #1. Below are some related links that should help.
witch is the 6th cylinder
Below are attached links discussing the horn on your truck.
Get a manual on your truck from DISCOUNTAUTOREPAIRMANUALS.COM They are about $9
The torque specs for the cylinder head on a b2200 are 59-64 ft lbs (cold).
It would depend on the truck's condition. The B2200 short bed truck in excellent condition would be about $1,650. The B2200 long bed would be around $1,750 in excellent condition.
I have a 92 b2200 with 325k miles. Ibought it brand new.
At the top of the clutch pedal in the cab of the truck.
All the 1986-1993 mazda b series trucks were manufactured in japan.By the way great built trucks for that matter.
Look under vehicle follow fuel line from tank
How do you reset computer on 1989 Mazda B2200 PU truck? We seem to be having a key turn loop on computer and after so many starts the truck starts stalling out. Have cleaned computer 2 times now and problem seemed to go away but after similar time period usually a week the problem started again.
All 1986-1993 models have the same doors.
The amount of liability a driver has to carry, is decided by the laws of the state in which they live.
she would get hot or leak or you would hear a funny noise in the front
Gap is 0.031 or 31thousandths. your truck has the 2184 cubic inch engine.
Ummm no where??!!?! for one a b2200 is a Mazda pick up and in that case it would be on the drivers side half way back affixed to the inner side of the frame rail :P simalair location on either truck though
This has been answered and do a seach and it will take you step by step and word it just as you placed your question about it!
Mazda made a b2200 and b2600 truck in 1989.As for performance the engine is rated at 85hp or so and really just a mpg truck not a power house for dragging trailers or too much weight.The truck is great for general use,and driving and hauling resonable things in the bed with ease over all.
The firing order is 1-3-4-2 with cylinder one being towards the front of the truck. I've attached some additional links for you below that may help you.
Public libraries usually have repair manuals (Chilton or Haynes) available for checkout.
The B2200 does not have "scan tool" capability. It does have a diagnositics port that can be used to throw out codes using the MIL light in the dash. There are about a dozen codes that at best tell you the obvious. There is lots of help on mazdatruckin.com that can help you diagnose your truck.
You can put another Mazda truck engine in place of the original.Now it does not matter if it is out of a automatic or manual transmission truck.The 1986-1993 are interchangeable.The things that do matter is if the truck is has a b2200 or b2600 it has a different ecm (electronic control module) the computer which is made specifically to run with those engines due to sensor and if it is carburetor and or fuel injected.So if you want to upgrade the engine to the b2200 the engine harness going to the ecm may be different but NOT sure (myself) on this .However if you do go with the newer engine it will require the ecm for a b2200 truck .I suggest checking with a local Mazda dealer to see if the harness is compatible it probably is but checking is a good idea.There is not much difference in the b2000 to b2200 in terms of basics the only real difference is cubic inches the 2000 is 1998 cu and the 2200 is 2184 cu.Unless someone else has knowledge other wise this is my suggestion.Hope this helps and if I left something off or incorrect may others correct my post.
Check on the passenger side, near the firewall. In my 91 B2200 it is a plastic inline filter, held in by two hose clamps. Takes about 90 seconds to replace. There is also one at the inlet of the gas tank.