Without a lot more info on what motor you have it is impossible to tell you what your firing order is, and i would only Google it anyway (which i guess you can do yourself)
So instead i have given you a way to work it out for any motor.
I'm not sure if you meant to say 20Lt or 2.0Lt so i am going to answer the question as it was written, however the method is the same for a 2.0lt as a 20lt.
First take a piece of paper and down the left side write the number of cylinders you have, ie. write the numbers 1 to 12 if its a V12 or 1 to 10 if its a V10 ect.
Second go remove the rocker covers off the motor so that you can see the top of the valve stems (don't disassemble the valve train though)
Now hand crank the motor so that piston 1 has its intake valve just beginning to open.
On your piece of paper you can now write a 1 next to the 1 already on your piece of paper.
Now continue to hand crank the motor and watch carefully for the next intake valve to open. work out which piston it is and write its number next to the number 2 on your piece of paper.
Continue in this fashion and eventually when you fill up the second column on you piece of paper you will have your firing order read from top down in that column.
Now lastly before you do anything else, go down and by the service manual for you motor / car and do a lot of reading before you go pulling stuff apart again.
Your question demonstrates that you do not yet have the requisite knowledge to do more than top up your water and oil, but thankfully that's easy to fix.
2.4 liter Duel over head cam (DOHC) ka24de
Drivers side head front to rear is 1-3-5-7 The other head is front to rear 2-4-6-8 Firing order is--1-8-7-2-6-5-4-3
Rear head 1,3,5Front head 2,4,6Firing order 1,2,3,4,5,6Rear head 1,3,5Front head 2,4,6Firing order 1,2,3,4,5,6
what are the head tourque specs for a 1986 Oldsmobile calais 2.5 liter ?
Firing order is 1-8-7-2-6-5-4-3Drivers side head front to back are cylinders 1-3-5-7The other head front to back is 2-4-6-8
He shot himself in the head on Dec. 31, 1971.
1-8-4-3-6-5-7-2 clockwise. Firing order on drivers side head front to back is...1-3-5-7 cylinders The other head front to back is...2-4-6-8 cylinders
The firing order of almost all engines is stamped into the intake or head.
Firing order is 1-8-7-2-6-5-4-3 Driver's side head front to rear is--- 1-3-5-7 The other head...........................-----2-4-6-8
all depends who your facing and how. you could play a nice, friendly duel for fun, or a duel with a bet for money, or a tounament duel to win the cup/ribbon/prize money, or be forced to duel with a gun pointed at your head, and lose your life, or if your dueling in the shadow realm, if you lose, you lose your mind, ect.
The 2006 Ford Super duty 5.4 liter engine had temperature sensor is located on the side of the head. The sensor is near the front of the head.
The head bolt torque specification for your Toyota 3.0 liter engine is 150 pounds. The head bolts should be torqued in 50 pound intervals.
The 1999 Dodge 3.3 liter cylinder head bolts should be torqued at 160 pounds psi. The head bolts should be torqued in 40 pound intervals.
1-8-7-2-6-5-4-3 Driver's side head front to back is 1-3-5-7 cylinders. The other head..........................is 2-4-6-8 cylinders.
A 3.8 liter V6 , which is an over head valve / pushrod design The GT has the 4.6 liter single over head cam ( SOHC )
You fail to mention if it is a 4 cylinder or V6. On the 2.4 Liter 4 cylinder the firing order is 1-3-4-2. Standing in front of the car looking at the engine from left to right the cylinders are 1-2-3-4. On the 3.0 Liter V6 the firing order is 1-2-3-4-5-6. Standing in front of the car looking at the engine from on the cylinder head nearest the front of the car the cylinders are left to right 2-4-6 and the rear cylinder head nearest the windshield left to right is 1-3-5.
The 1996 Ford Escort 1.9 liter engine cylinder head bolt torque specification is 120 pounds. The head bolts should be torqued in 40 pound intervals.
do it in the firing order it 's easier: 1-4-2-5-3-6
The firing order should be cast into the intake manifold. It may take some work to find it but it should be there.
The 3.0 liter " Vulcan " V6 engine is an over head valve / PUSHROD design ( The 3.0 liter " Duratec " V6 engine is a Dual Over Head Cam design so it doesn't have pushrods )
4.6 liter engine.
The 1.8 liter - 4 cylinder is NOT an interference engine , but the 2.0 liter - 4 cylinder is an interference engine
Either the 4.0 liter OHV ( over head valve ) V6 or the 5.0 liter V8