answersLogoWhite

0


Best Answer

It depends on whether it is automatic or manual. Between 6 - 8 degrees BTDC should be okay.

User Avatar

Wiki User

โˆ™ 2006-12-28 11:09:26
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: What is the ignition timing for a Mazda 323 1.4 engine?
Write your answer...
Submit
Related questions

What is the ignition timing for a Mazda 323 1991 DOHC B5 engine?

ignition problem


What is the ignition timing for 94 Mazda 323?

timing problem?


What is the timing setting's for a Mazda 323 E5?

Mazda 323 familia valve timing set up


What is the ignition timing on a Mazda 323 1989 b5 1.5l motor?

The igniton timng is 6 degrees BTDC


What are the timing angles for 1991 Mazda 323 1.6 liter petrol engine.?

Between 6 - 8 degrees BTDC


How often you have to change a timing belt on Mazda 323?

It should be changed every 60,000 miles on all years 1988-94 with a timing belt. It is not an interference engine.


Is it possible an electrical problem on a Mazda 323 can cause the engine coil to burn?

Is it possible an electrical problem can cause my engine coil to burn on my Mazda 323


When to change timing belt on 1600cc 323 Mazda 2003?

I was looking at the Gates website ( they make timing belts etc. ) and for the 1600 cc engine in a 2003 Mazda Protege ( Canada ) it shows ( 60,000 miles )


If a timing belt snap on Mazda 323 does it bend the valves?

If the engine is a non-interference type then the answer is NO. See the list below:


How do you remove an ignition lock cylinder from a 1988 Mazda 323?

With an uncle and a hammer.


What do I do on my 1990 Mazda 323 when the key won't turn in the ignition anymore?

i suggest u either get a new key or ignition


Can I disconnect the timer for my Mazda 323 ignition light that stays on?

no. you have to take the whole light out


Where is the dipstick located on a 1991 Mazda protege 323?

IF ITS A 1.8, THEN ITS NEXT TO THE TIMING COVER


What carb is fitted into a BD Mazda 323 with E5 engine?

Hitachi 2V is listed for the 323 1.5Ltr E5 engine (1981-1985).


Does a 1990 Mazda 323 have an interferance engine?

NO. Gates belts has a list. This engine is not interference.


Where can you get a wiring diagram for a 1989-1993 Mazda 323 hatch back 1300cc?

The Mazda 323 of that time from had a 1600cc engine but that isn't going to effect the issue of where to get a wiring diagram. Haynes makes a manual for the 1990-1994 Mazda 323. If you have a 1986-1989 Mazda 323, you will need to get a FSM (Factory Service Manual).


Can you put a Turbo Engine in a 1988 Mazda 323 SE?

SURE.


What engine oil is best for a Mazda 323?

shell 10w-40w


My 1991 Mazda 323 has two plastic screws on drivers side facing engine. Are they air bleeder valves?

My 1991 Mazda 323 has two plastic screws on drivers side, facing engine. Are they airbleeder valves?


What is the spark plug gap needed for a 2001 Mazda 323 1.6l engine?

1.00-1.10mm


How do you change the timing belt o thr Mazda 323 familia 1999 year?

sistem pemasangan temingbelt


Where is the oil dipstick located on a 1993 Mazda 323?

it is to the left of the engine beside your belt.


How do you fix a 1981 Mazda 323 clutch?

unbolt tranny from engine clutch is between them


Mazda 323 1.6i GT?

Mazda made a 323 "GT" turbo 4 door sedan for at least 2 years, 1988 and 1989. It featured the 1.6 DOHC (B6T) engine that was also standard for the 323 GTX. It was rated at 132 bhp.


Does the BMW 323 2007 need a timing chain change?

I doubt it. Timing chains are designed to last the life of the engine.

Study guides

๐Ÿ““
Create a Study Guide