Jeep Cherokee Sport
Mitsubishi Diamante
Toyota RAV4

What is the location of the gas cap cover release on a 1994 Jeep Cherokee Sport?

242526

Top Answer
User Avatar
Wiki User
2009-01-19 22:56:41
2009-01-19 22:56:41

on the floor, to the left of the driver's seat press the front edge or rear edge.... it is what i found on mine...

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Look directly below the front of the engine (valve cover) follow the top water hose from radiator to the engine. The actual thermosat is inside the themosat housing.

User Avatar

Most likely it is in the power distribution box located on the passenger side of the engine compartment just aft of the battery. Open the cover, there is a diagram on the underside of the cover.

User Avatar

The brake light fuse on a 2003 Jeep Grand Cherokee can be found by looking at the cover to the main fuse box. It identifies each fuse and its location.

User Avatar

try looking under the cover of the fusebox that is on the right hand side under the bonnet ..... cheers Aussie charlie...........

User Avatar

On the fuse box cover, there is (in very small print) a diagram of the fuses and there location. Hope this helps! rj

User Avatar

The 1999 Jeep Cherokee windshield washer pump fuse is in the fuse box. The fuse box is in the engine compartment. The location of the fuse will be listed on the inside cover of the fuse box.

User Avatar

under the dash on the right side there is a cover over it pull the glove box it might help

User Avatar

On the right side fender under a plastic cover there are 4 square relays.

User Avatar

The 1997 Jeep Cherokee fog light relay fuse can be found in the fuse box. The fuse box is located in the engine compartment. The location of the fuse can be found on the inside cover of the fuse box.

User Avatar

The 1998 Jeep Grand Cherokee windshield wiper fuse is located in the fuse box. The fuse box is in the engine compartment. The location of the fuse is listed on the inside cover of the fuse box.

User Avatar

On the thermostat housing. Top, front(towards radiator), center of valve cover. It's aluminum and you can't miss the wire harness attached to it.

User Avatar

You have to remove the brakes, rotors, wheel hubs, axle shafts, diff cover, and differential carrier, seals are on the inside of the axle tubes.

User Avatar

the theme of location covers the location of a place or he location of someone. MARCU$ I. TORRE$ $.

User Avatar

The Cherokee idians built there houses with wood and hay to cover the holes iv the longhouse.

User Avatar

Inside the dome light fixture. Slide it forward about 2 inches and it will drop off the clips. Control module is mounted inside the cover.

User Avatar

the valve cover torque specs are 85in lbs

User Avatar

I know the Cherokee does. If the Grand Cherokee does, check the diagrahm on the fuse panel cover. or owners manual.

User Avatar

In the under hood fuse box. The cover will have the location.In the under hood fuse box. The cover will have the location.

User Avatar

Fill to level with the hole in the cover.Fill to level with the hole in the cover.

User Avatar

The Jeep Cherokee 2.5 liter diesel engine fuel injection sensor fuse can be found in the fuse box. The fuse box is located in the engine compartment. The location of the fuse will be listed on the inside of the fuse box cover.

User Avatar

Hey having the same problem. I have no clue what i am doing but this web site has helped me maybe it can help you. http://www.cherokee-jeep.com/1-2swremov.htm good luck

User Avatar

According to the service manual the ASD is located in the Power distribution center. This is under the hood, behind the battery. the ASD relay location is noted on the cover of the power distribution center. Full service manual for the 96 GC is available on pdfoo.com

User Avatar

The 2001 Montero radio fuse is in the fuse box. The fuse box can be located in the engine compartment. The location of the fuse will be listed on the inside cover of the fuse box.

User Avatar

The 2001 Mitsubishi Montero Sport 3.0 liter engine valve cover torque specification is 40 pounds. You do not want to over torque the valve cover bolts, as you may ruin the valve cover gasket.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.