answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered 2006-12-31 23:54:09

the pressure switch sends a signal to the ecm[computer] when you turn to increase engine rpm a small amount to make up for power loss.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still Have Questions?

Related Questions

Where is the power steering pressure switch located on a 97 Toyota Camry le v6?

Power steering power steering pressure switch is a part of power steering pump. There is wire harness connect to the pump, it's connect the switch. Find the harness you will find the switch.


Where is the power steering pressure switch for a 1993 chrysler new yorker?

The power steering pressure switch, on a 1993 Chrysler New Yorker, is located below the power steering pump. The pressure switch is attached to the power steering reservoir mounting bracket.


Where is the 1997 Lincoln Town Car power steering pressure switch located?

On the back of the power steering pump.


Where is the power steering pressure switch do on a 2002 Toyota Camry?

The switch is sitting directly in the power steering pump, and can trace by locating the wire connected to it.


Where is the power steering fluid pressure switch?

On my mondeo mk2 its located next to the power steering pump, which is next to the cambelt


Where Is the power steering pressure switch on 2003 Mazda protege?

Right on the power steering pump. pointing to the front of the car.


Where is the power steering pressure sensor switch located on a 99 avenger?

The power steering pressure sensor is located on the front of the power steering pump. It is circular and has one wire going to it.


Where is the power steering pressure switch located?

Usual location is in the pressure line between the pump and gear.


Where is the power steering pressure switch in 2000 dodge Dakota 2 wheel drive?

it is on the pressure line off the power steering pump itself on the right side of the pump (if looking at the motor)


Where is the power steering pressure switch on a 2004 Mitsubishi Endeavor?

The pressure switch is located on the back of the power steering pump which is on the passenger side of the car at the rear of the engine. You can reach it from top or bottom but I found, to take it out it is easier to reach from under the car. It is the only part of the power steering pump that has a wire going to it.


Where is the oil pressure switch on a 96 ford windstar van?

The oil pressure switch is right under the alternator bracket or power steering pump


What is the output of a Power steering pump?

The output of a power steering pump is the high pressure side which goes to the steering box. It creates hydraulic pressure which makes steering much easier.


Your power steering pump is leaking and you replaced the pump what do you do its a 2001 Pontiac sunfire?

Have you checked the power steering pressure line?


How to replace a power steering pump in a 2001 ford focus?

If you have a 2.0L Zetec-E (Zetec): Removal Remove the accessory drive belt. Disconnect the power steering line from the power steering pump. Allow the fluid to drain into a suitable container. Remove the power steering pump lower retaining bolts. Disconnect the power steering pressure (PSP) switch electrical connector. Depress the locking tang. Disconnect the power steering hose from the power steering pump. Allow the fluid to drain into a suitable container. Remove the power steering pump upper retaining bolts. Raise and support the vehicle. Remove the power steering pump. Remove the PSP switch. CAUTION: Make sure vice jaw protectors are used. Secure the power steering pump in a vice. Using the special tool, remove the power steering pump pulley. Installation Using the special tool, install the power steering pump pulley. NOTE: If installing a new power steering pump, the unions that are supplied fitted to the pump should be removed and retained for future use. Using the special tool, install a new O-ring seal onto the steering gear to power steering pump union. Push the new O-ring seal onto the special tool. Locate the special tool onto the union and install the O-ring seal. Install the PSP switch. Remove the power steering pump from the vice. Install the power steering pump. Install the lower retaining bolts. Connect the power steering line. Lower the vehicle. Install the power steering pump upper retaining bolts. Connect the power steering hose to the power steering pump. Connect the PSP switch electrical connector. Install the accessory drive belt. Fill the power steering system. If you have a 2.0 SPI engine: Removal Detach the accessory drive belt from the power steering pump pulley. Using a


Diagrame of power steering system?

Power steering systems can be diagrammed into two chief components. These are the power steering pump and the rack-and-pinion steering gear. The power steering pump sends pressurized fluid into the rack which moves the gear actuating the tie-rods, which moves the wheels in the desired direction. The power steering pump has a low pressure return line and high pressure out one.


What is the purpose of the pressure switch in the power steering pump and what does the computer do with 2005 Toyota tacoma?

when the pressure gets high in the power steering system, its harder to turn the pump. when the pump is hard to turn it slows the engine rpms, acting a little like a brake on the engine. this sensor tells the computer how much pressure there is in the system and increases the idle to compensate for it.


Where is Power steering pressure switch location Jeep liberty?

It's the only hose from the power streering pump, with the electrical connection to it. The hose has a Tee built into it , with the sensor switch and wiring attatched.


How do you remove the solenoid switch and pressure line manifold on a power steering pump for a 1998 Chevrolet Cheyenne with 5.7 liter engine?

carefully


Where is the power steering pressure sensor located on a 2007 Toyota tundra?

On the back side of the power steering pump


How much does a power steering pump?

A power steering pumps as much as the power steering pump can pump.


How to Remove power steering pump on mystique?

Remove the power steering pump hose. Remove the power steering pump belt. Remove the power steering pump retaining bolts. The power steering pump will come off.


What is the average output pressure for car Power Steering Pump?

1000psi


How much pressure in a gm power steering pump?

1,000 psi


Can the power steering pressure switch cause a car to act like it is low on fluid?

No, I don't believe there is a pressure switch. And nonetheless, it's most likely a weak pump. If it doesn't whine, and is just hard to turn the wheels, chances are it's a weak pump.


Where is the oil pressure switch located on a 93 Ford Ranger 40L V6?

the oil pressure switch is located on the left side below the power steering pump. it is about 1.5 - 2 inches and about 2.5 inches long