Top Answer
User Avatar
Wiki User
Answered 2014-08-22 16:35:39

A 115hp Mercury outboard boat motor has a fuel to oil ratio of 50 to 1. This translates to 16 ounces of 2-cycle oil to every 6 gallons of fuel.

User Avatar

Your Answer

Related Questions

The dry weight of an 1990 model, 115 Mercury outboard is 326 lbs.

Not sure of 1970, but I have a 1983 and it weighs 365 lbs. That's probably pretty close

The 1979 - 1980 model, 115 hp Mercury outboard, requires a 50:1 ratio. One pint of 2 cycle oil, to six gallons of fuel.

How much doe a 1997 2 stroke johnson outboard motor weigh

The fuel to oil ratio for a 1977 model, 115 hp Johnson outboard, would be 50:1, roughly one pint of 2 cycle oil, to six gallons of fuel.

Mercury Marine used the blue colored cowling band during the period of mid 70, to early mid 1980. All Mercury outboards manufactured in this era, require a 50:1 ratio, one pint of 2 cycle oil, to six gallons of fuel.

I am not certain of the exact model(s) involved, but there was a recall issued for oil pump replacement on the earlier 4 stroke model. Check with a Mercury Marine dealer to see if applicable to your engine, also through looking up your engine serial number, it can be determined if your engine has already been repaired through any recall campaigns.

The last listing I have on an in-line six, 115 Merc, is the 1986 year model. The dry weight is listed at 315lbs, this is with integral trim. I would think the 1976 model a little lighter at 290-300lbs, due to having external trim system.

it should probs have a motor beetween 70 and 115hp check the hp rating on your boat on the capacity plate

it could of been a short in the wiring in the engine compartment or you had a fuel leak and it got into wires or the ignition system

The maximum speed of the bergantin 6cyl 115HP 1962 is 137 miles per hour.

The maximum speed of Estanciera manual 6cyl 115HP 1960 is 220 km per hour.

The maximum speed of the Estanciera IKA manual 6cyl 115hp 1961 is 220 km per hour.

The maximum speed of 1962 rover 3 litre automatic 6cyl 115HP is 92.1 mph or 148.2kph.

That serial # dates to Feb.-Mar. 1936. Only 250 was made during that year. A good core will bring between 10-15K. If it runs you could be looking at up to 30k. A very rare engine.

The 1999 Chevrolet Cavalier 2.2L engine has 115HP

The 1999 Chevrolet Cavalier 2.2L engine has 115HP

for most of these motors any tech manual from Johnson would mostly cover 90% of all of you questions... however wiring schematics are very diffrent and I have been looking for a wiring diagram for a Johnson stinger II motor, not included in any recent manuals, so if anyone knows where to find one let me know

110-115bhp 8v (depends on who you talk to) 134BHP 16v The owners manual says it was 115hp at 5300 rpms. 115hp, 122 lb/ft. i think its 102hp at the wheels, give or take one or two. not sure about the torque

The Model number on all late model and most early model Johnson and Evinrude outboard motors year of prduction is determind using the word 'INTRODUCES' (1234567890). Confused? On a standard year 2000 115HP Johnson two stroke outboard motor you might have the model # J115VLSSS: J - Johnson 115 - Hp rating V - Design features (V=White Paint) L - Shaft Legnth (20inch) SS - Year Of production (2000, ER = 1994) S - Sufix (Stuff ya don't need to worry about) So there you have it. Safe boating!

No difference whatsoever .... zero ... nada ... zilch !

The dry weight of a 1995 Evinrude 115hp is between 293 and 306lbs. depending on the model.

With the 3 speed manual trans, 91 mph.With the automatic trans, 90 mph.