Head Gaskets and Valve Covers
Geo Storm
Honda Civic SI

What is the proper head torque for a 92 Geo Storm GSi 1.8 engine?

454647

Top Answer
User Avatar
Wiki User
2005-04-15 14:03:44
2005-04-15 14:03:44

First step is 29ft lbs and the second and final step is 58ft lbs intake side *10 *6 *2 *3 *7 header side *9 *5 *1 *4 *8 make sure you follow this patter when tourqueing head bolts and removeing head bolts to.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

What is the cylinder head torque specs for a 2001 daewoo nubira 2.0 litre engine and what is the proper torque order

User Avatar

the proper torque specification for the geo storm 1.6 engine is 58 ft lbs ... Always torque in a spiral from the center outwards. Make sure you cleaned up the threads in the block ith a chaser (NOT a tap) before proceeding. And oil the threads on the new head bolts. You should be able to turn the bolts all the way snug with your fingers if the threads are cleaned up correctly. Then torque in 3 stages to the final torque in a spiral from the inner bolts.

User Avatar

head torque sequence, ft lbs, 4239d jd engine

User Avatar

The head bolt torque specification for a 3.3 liter engine is dependent upon the manufacturer of the engine. In general, the 3.3 liter engine had bolt torque specifications is 120 pounds.

User Avatar

The proper torque is 26 Ft-lbs due to the aluminum head.

User Avatar

What is the proper head bolt torque for a 89 toyota camry 2.2?

User Avatar

what is the torque setting for the head bolts on a 2007 chevy malibu with a 2.2L engine

User Avatar

torque for 2c engine cylinder head bolts

User Avatar

The head bolts on the Nissan 2.7TD can vary depending on the engine. If the engine is a diesel cargo or serena, the cast iron head has about 80 foot-pounds of torque, but if it's a smaller petrol engine, the bolt head has a 60 foot-pound torque.

User Avatar

HEAD BOLT TORQUE For your 1999 PONTIAC GRAND AM: HEAD BOLT TORQUE FOOT POUNDS (FINAL TORQUE) TORQUE SEQUENCE --------- | 6 2 3 7 | | 5 1 4 8 | --------- STEP 1: TORQUE IN SEQUENCE TO 33 FT/LBS STEP 2: TURN AN ADDITIONAL 90 DEGREES RECHECK FINAL TORQUE IN SEQUENCE *** CAUTION *** ENGINE USES TORQUE TO YIELD HEAD BOLTS (TTY) THAT PERMANENTLY STRETCH DURING THE INITIAL INSTALLATION. NEW HEAD BOLTS MUST BE USED WHEN CYLINDER HEAD IS REPLACED OR RE-INSTALLED TO OBTAIN PROPER TORQUE. ALWAYS COAT BOLT THREADS WITH THE PROPER SEALANT.

User Avatar

what are the torque settings for a mitsubishi 4m51 engine

User Avatar

what is the torque on the head bolt and sequence for a ford 3000 diesel engine.

User Avatar

Cylinder Head Torque is 190 inch pounds or 22.0nm

User Avatar

I am installing a head for kia j2 engine I would like the torque settings and the steps

User Avatar

standard torque on any head is about 80 lbs to 90 lb torque

User Avatar

The 3800 Pontiac engine had bolt torque specification is 160 pounds. The head bolts should be torqued in 40 pound intervals.

User Avatar

whar are the torque specs for head bolt on a 1999 Mazda protege 1.6 engine

User Avatar

what are head bolt torque rod bearing cap torque on k4n mitsubishi

User Avatar

The cylinder head bolt torque specs for a 1972-1979 Toyota 2TC 1600 engine is 64-68 ft lbs.

User Avatar

Please ask a new question with more info such as year, make, model, and engine size.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.