answersLogoWhite

0


Best Answer

The best way to find out is go to your local auto parts store, ask for a haynes or chiltons manual on your vehicle. This will tell you everything you need to know about working on your vehicle. It is a delicate job, make sure nothing falls into the motor & use the proper torque specs & sequence on your bolts otherwise you will crack or warp the aluminum manifolds.

User Avatar

Wiki User

โˆ™ 2005-11-06 18:52:23
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: What is the sequence for installing lower intake manifold on a 98 31L Lumina?
Write your answer...
Submit
Related questions

How do you change the intake manifold gasket in a 3100 Chevy lumina?

take it to a mechanic


What are the torque specs and torque sequence for a 1992 Nissan Maxima intake manifold?

what are the torque specs and sequence for a 1992 Nissan maxima manifold


What is the torque specification for the lower intake manifold on a 97 3.1L lumina?

10 ft lbs


What causes a surge in a 1993 Chevy lumina 3.1 sedan?

Try cleaning the intake manifold.


What is the Intake manifold torque sequence 455?

35 ft pounds


What is the torque sequence for intake manifold on a 1997 mercury cougar 4.6liter?

The 1997 Mercury Cougar 4.6 liter engine intake manifold torque sequence should begin at each end of the manifold. Keep moving towards the center and alternating from and to end.


How do you know if your intake manifold gasket is bad?

You will feel a miss at idle and the idle speed may be erratic. Try retorquing the intake manifold bolts, working from the center out in the recommended tightening sequence. If that fails, the intake manifold will have to be removed and the intake gaskets replaced.


How do you know if Intake manifold gasket is bad?

You will feel a miss at idle and the idle speed may be erratic. Try retorquing the intake manifold bolts, working from the center out in the recommended tightening sequence. If that fails, the intake manifold will have to be removed and the intake gaskets replaced.


Where can you find a diagram for installing a intake manifold gasket on 2003 Chevy venture?

is their a web site, that will provide me with the a print out for the intstalling of a intake manifold gasket for a 2003 chevy aenture.


Do you add horsepower by installing an edelbrock intake manifold and carburetor?

Probably not. Unless the previous intake and carb were not functioning properly.


1999 lumina ran hot and then i changed out the water pump and the thermostat but still red lining I was told it might be the intake manifold gasket seal is this correct how much should it cost to fix?

that's what it is, i have a lumina, had same problem, replaced the intake manifold. run like a top since


How can you tell if inlet manifold is faulty?

You will feel a miss at idle and the idle speed may be erratic. Try retorquing the intake manifold bolts, working from the center out in the recommended tightening sequence. If that fails, the intake manifold will have to be removed and the intake gaskets replaced


Where is the egr valve on a 2000 Chevy Lumina?

The EGR valve on a 2000 Chevrolet Lumina is located inside the intake manifold. A replacement valve can be purchased at any auto parts store.


Intake manifold bolts torque ford windstar?

2000 3.8 Lower intake manifold (manifold to cylinder head) 1st step is 44 inch pounds, 2nd step is 89 inch pounds. This must be done in sequence.


Intake manifold torque setting for intake manifold?

diferential pressure sensor intake manifold plausibility


Cost of replacing an intake manifold on 1999 Chevy lumina?

upper or lower? if it's lower you can bet on paying upwards of 400$


What are Torque specs for 1994 350 intake manifold?

Intake bolts should be torqued to 35 ft lbs in the appropriate sequence. There should be 12 total "intake" bolts


What is the torque sequence on a 351 Windsor intake manifold?

just start in the middle and tighten in circler pattern


What is the torque sequence for a 2000 5.7 intake manifold?

Start on the inside do an X pattern and work your way out


What is bolting sequence and torque on a 1989 Chevy 350 intake manifold?

the sequence is the two center bolts on each side, the work your way outwards


1995 olds 98 upper intake manifold torque sequence?

I found this in the local library that had chiltons manuals.


Where is the intake manifold gasket located?

between the head and intake manifold


How do you change intake manifold on Isuzu trooper?

remove intake manifold.


Where is the intake manifold gasket?

Between the intake manifold and the cylinder head.


97 lumina overheats while idleing?

start with water pump. If its a V6 3.1L have the intake manifold gasket checked. You may have a coolant leak.

Study guides

๐Ÿ““
Create a Study Guide