0
What is the significance of negative values of voltage and current?
Wiki User
∙ 14y ago
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What is the significance of negative values of voltage and current in the digital VOM?
The significance of negative values of voltage and current in the digital VOM is to show the accurate and full power that a particular device or equipment has in the result.
What is the significance of obtaining a negative reading in testing voltage?
Electric current can flow in one of two directions in a wire; with alternating current, the direction changes continually, back and forth. The use of positive and negative values for voltage gives you a direction for the voltage. If current flowing to the right is positive, then current flowing to the left is negative.============================Answer #2:A negative reading indicates that the point to which the positive probe ofthe voltmeter is connected is at a lower potential than the point to whichthe negative meter probe is connected. It tells nothing about the circuitconditions except in combination with the knowledge of how the meteris connected.
How can instantaneous current values be determined?
Voltage divided by the resistance of what ever you want to measure the current in.
Why do the readings differ for increasing and decreasing values of the incandescent lamp voltages?
...what readings? current? voltage? power? lux?
What is the relationship between peak rms and average values of an ac voltage?
Peak voltage of an AC voltage is the value at its highest or lowest point.RMS (Root Mean Square) voltage of an AC voltage is a mathematical derivation involving the square root of the average value of the squares of samples of the voltage as the sample interval approaches zero.Average voltage is simply that - the average or mean voltage.For a true sine wave, RMS and average are equivalent, but they are not equivalent when the wave is distorted, or has some other shape such as triangular.RMS is the best way to measure an AC voltage, as it gives you a true reading of the amount of power that the voltage can deliver.One issue with non-RMS AC meters is that they typically measure the rectified, filtered peak value and then compensate by dividing by 1.4. This is not correct unless the voltage is a sine wave.AnswerThe peak value of an a.c. voltage or current is the amplitude of that voltage or current waveform -i.e. the maximum value of voltage or current in either the positive or the negative sense.The root-mean-square (rms) value of an a.c. voltage or current. For a sinusoidal waveform, the rms value is 0.707 times the peak value (amplitude). A.C. voltages or currents are always quoted in rms values unless otherwise specified.The average value of an a.c. voltage or current is zero over one complete cycle so, when used, it applies only over one half cycle. Therefore, the average value for one-half cycle of a sine wave is 0.637 times the peak value. Average values are of little relevance to a.c. calculations.
What is the significance of negative values of voltage and current in the digital VOM?
The significance of negative values of voltage and current in the digital VOM is to show the accurate and full power that a particular device or equipment has in the result.
What is the significance of obtaining a negative reading in testing voltage?
Electric current can flow in one of two directions in a wire; with alternating current, the direction changes continually, back and forth. The use of positive and negative values for voltage gives you a direction for the voltage. If current flowing to the right is positive, then current flowing to the left is negative.============================Answer #2:A negative reading indicates that the point to which the positive probe ofthe voltmeter is connected is at a lower potential than the point to whichthe negative meter probe is connected. It tells nothing about the circuitconditions except in combination with the knowledge of how the meteris connected.
How can instantaneous current values be determined?
Voltage divided by the resistance of what ever you want to measure the current in.
What is term used when an Alternating current acts like a direct current?
Perhaps you are asking how the voltage of alternating current is measured, to be equivalent to the voltage of a direct current system. Alternating current and direct current have distinct properties. With direct current, voltage is at a constant polarity, and a direct current voltage source will maintain a uniform, constant voltage level. Alternating current reverses polarity at a given frequency and therefore it's voltage continuously varies from a positive peak voltage level, through zero, to a negative peak voltage level, repeating this cycle continuously. For this reason, voltage of an alternating current system, is measured in root-mean-square (rms), which is a voltage, which when multiplied by the current in amperes, calculates power which is equivalent to that of direct current of the same voltage and current values. With a typical sinusoidal waveform, the peak voltage of alternating current is divided by the square root of 2 to determine the rms voltage. The 120 volts output in the wall outlet in our home is actually about 170 peak volts.
How do you make a LED light?
A: Most LED needs a minimum voltage and minimum current in the right direction positive anode negative cathode to light up. Unfortunately the voltage can be as low as 1.2 to 5v and the same apply to the current from 5ma to 500ma. So there is no set values it depends on the device.
How do you make LED lighting?
A: Most LED needs a minimum voltage and minimum current in the right direction positive anode negative cathode to light up. Unfortunately the voltage can be as low as 1.2 to 5v and the same apply to the current from 5ma to 500ma. So there is no set values it depends on the device.
When is it important to make sure to match the polarity of the meter leads to the polarity of the circuit being tested?
This is important when meter cannot display negative values, e.g. it is analogous meter with scale. Most digital meters can display negative values. P.S. I am amateur in elecrtonics.
How do you verify omh's law using multi tester?
if your looking for current (I) = voltage ./. resistance voltage (v) = current x resistance resistance (r) = voltage ./. current plug in your values calculate them then use meter to see if they match!
How will the current change if the voltage in a circuit is reduce while the resistance remains constant?
The current will drop. Y??See it this way - resistance is something that opposes current flow. Voltage is the one that helps the current to get across the resistance. So if u have a high resistance, u need a high voltage to get the same current across.But all the values are solely dependent on the output required.Hope that helps.
What is apparant power?
Apparent power is the combined power value that is obtained by allowing for the different values of current and voltage.
Why do the readings differ for increasing and decreasing values of the incandescent lamp voltages?
...what readings? current? voltage? power? lux?
What is meaning oof rated values of current voltage power and torque of an electrical machine?
What it means is that those rated values may not be exceeded, they are the maximum that the machine can take.
