answersLogoWhite

0


Best Answer

The third brake light cover just has two screws that have to be removed. Then you can pull the unit out and turn the light socket to remove it from the cover. Pull the bulb straight out of the holder and replace. On the side lights you have to open the tail gate and remove the screws on the inside of the doorjam. After that the lens pulls straight out(like your light is backing away from your van.)There are three pins in rubber sockets that hold the lens in place and prevents raddles. The pins just pop in and out but can fight you a little, just be careful to not break the pins off. Once the cover is off, twist off the desired socket and pull the bulb out, replace the bulb and reinstall the cover. Hope this helps. -JB

User Avatar

Wiki User

โˆ™ 2006-12-03 22:40:00
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: What is the specs for the center tail light bulb on a 95 Mercury Villager so that you can replace it?
Write your answer...
Submit
Related questions

Where can you buy a center light for a 1995 Mercury Villager?

walmart


How do you replace light bulb on high mount brake light on 1998 Mercury Villager GS?

Just unscrew it.


How do you replace the shift indicator bulb on a 98 Mercury Villager?

The instrument cluster must be removed to replace the light bulbs on it.


How do you replace Dash light bulbs in a 1995 Mercury Villager?

You have to remove the instrument cluster to get access to the bulbs.


How do you replace the light bulb in the dashboard of the car gears on a 2002 mercury villager?

You need to remove the instrument cluster.


How do you change the rear brake light bulb on your 2000 mercury villager sport?

Just unscrew the rear brake light, turn out the socket, and replace the bulb.


Why do the brake lights stay on 2001 mercury villager?

This is usually cause by a stuck brake light switch on the brake pedal. Replace it.


Why does the oil light flash on your mercury villager?

dont no lol xx


How do you change rear brake light 2001 mercury villager?

To change the rear brake light on a Mercury Villager, the tail gate must first be lifted. This allows access to the lens, which must be removed with a screwdriver. Then, the bulb may be replaced.


How do you reset the 'service engine soon' light on a 1999 Mercury Villager?

With an OBD2 scanner.


Where do you look when the check engine light on a 1994 Mercury Villager comes on?

dash dash


Where is the mercury villager hazard light switch?

Usually on the dash to the right of the steering wheel.


Where is the brake light switch located on a 1994 mercury villager?

On the brake pedal assembly.


How do you replace a fog light in a 2002 mercury mountaineer?

How do I replace the fog lights in my 03 mercury mountaineer


1996 Mercury Villager the check engine light comes on and off?

have vehicle scanned to determine problem


What to do when 98 Mercury Villager battery light is on?

This indicates a no-charge situation. Most likely the alternator is bad.


How do you reset check engine light on a 1994 mercury villager?

The easiest way is to unhook the battery for a minute.


How do you change the tail light of a 1995 Mercury Villager?

The bulbs screw in from the rear. There are screws holding the light assy on and youhave to take them out to take the light off.


How to troubleshoot a check engine light on a 1998 Mercury Villager?

Have vehicle scanned to determine the problem


Why is the gas light always on in 1996 mercury villager where the sensor has been changed twice?

The indicator was not or cant be reset.


2002 Mercury Villager brake light lights up on rough roads.?

Brake light switch needs adjusting or replacing. It is too sensitive.


How do you turn off the service engine soon light on a Mercury Villager?

Either have the problem that is causing the light to illuminate fixed or disconnect and reconnect your battery.


Where is the button to shut of the back hatch light on a 1994 mercury villager?

There is no separate switch for it. Pushing the light switch will defeat the dome and courtesy lamps.


O2 sensor problems with Mercury Villager?

If the o2 sensor is bad, replace it. If the sensors are activating the check engine light, then the codes should be checked. The catalytic converter could be blocked or the engine may not be running properly.


Where is the daytime running light control module in a 1994 mercury villager?

Inside the engine compartment by the passenger strut tower

Study guides

๐Ÿ““
Create a Study Guide