HomeWhat is the torque and sequence for replacing a head on a 1988 Mercury cougar 3.8 V6?
Wiki User
2004-11-30 06:27:13
2004-11-30 06:27:13
Just start in the center, and alternately, work your way towards the ends of the head.
Related Questions
The 1997 Mercury Cougar 4.6 liter engine intake manifold torque sequence should begin at each end of the manifold. Keep moving towards the center and alternating from and to end.
the 99 mercury cougar inline 2.0L engine has 125 hp and 131 lbs/feet of torque the v6 cougar 2.5L engine has 170hp and ? lbs/feet of torque
For my Mercury Cougar with Aluminum Heads it is:Torque Sequence 1993 3.8 Cougar; Looking at Engine from front of car the lower bolts are 7 3 1 5 upper bolts are 8 4 2 6. Step 1; Torque in Sequence to 37 FT./ LBS Step 2;Torque in Seq. To 45 FT./LBS. Step 3; Torque in Seq. To 52 FT,/LBS. Step4; Torque in Seq. To 59 FT./LBS. Step 5; Back off all bolts in Torque Sequence 2-3 turns. Step 6; Retorque all Bolts in Sequence 11-18 FT/LBS. Step7; Rotate Long Bolts 85-105 Degrees, Short Bolts 65-85 Degrees in Sequence. Recheck final Torque in Sequence. When replacing Head Gasket be sure to replace all torque-to-yield style Head Bolts. Hope I Have Helped -u-. "Odie" OdiebuiltMC@aol.com
Torque Sequence 1993 3.8 Cougar; Looking at Engine from front of car the lower bolts are 7 3 1 5 upper bolts are 8 4 2 6. Step 1; Torque in Sequence to 37 FT./ LBS Step 2;Torque in Seq. To 45 FT./LBS. Step 3; Torque in Seq. To 52 FT,/LBS. Step4; Torque in Seq. To 59 FT./LBS. Step 5; Back off all bolts in Torque Sequence 2-3 turns. Step 6; Retorque all Bolts in Sequence 11-18 FT/LBS. Step7; Rotate Long Bolts 85-105 Degrees, Short Bolts 65-85 Degrees in Sequence. Recheck final Torque in Sequence. When replacing Head Gasket Besure To Replace all Head Bolts. Hope I Have Helped -u-. "Odie" OdiebuiltMC@aol.com
140 horse power and 215 foot-pound torque
Torque sequence of what. Heads, wheels, etc.
torque sequence on what part? more info needed
what is the head torque sequence for a 1991 pathfinder
There is no torque sequence just torque rocker arm studs to the proper torque
Buy a Haynes manual because you have not given engine size and also you need to know the order of sequence in which to tighten them as you do not tighten them all the way first time. Usually you take 3 times around at 1/3rd recommended final torque ft/lbs, increases meaning the final or 3rd time you set the wrench at final torque specs.
what are the torque specs and sequence for a 1992 Nissan maxima manifold
Torque sequence------------ l 93157 l l 862410 l ------------ Step 1: torque in sequence to 44 Ft/LBS Step 2: in sequence completely loosen all bolts Step : retorque all bolts in sequence to 44 Ft/LBS Step 4: in sequence turn an additional 90 degrees Step 5: in sequence turn an additional 90 degrees Recheck final torque in sequence***CAUTION*** engine uses Torque To yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.
140lbs on your torque wrench
What is the Cylinder Torque sequence 2000 Pontiac Montana 3.4V6
the torque is 70 ft. lbs., but as far as I know there isn't a torque sequence.
Head Torque sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs recheck final torque in sequence.
what is the torque on the head bolt and sequence for a ford 3000 diesel engine.
The correct torque spec is 85 INCH lbs.
I assume you mean for the small cab over truck. there are way to many things that have a torque sequence to answer this question
in sequence torque bolts to 20nm, then again in sequence turn a futher 120 degrees, and again in sequence 120 degrees.
what is the engine code??
Head torque sequence for a 2002 3800
Your question is best answered with" purchase a manual"! Reason being, looking for help with torque numbers also requires sequence. Without the proper sequence, you will destroy, at the very least, the head gasket. an inexpensive manual can be found at all patrts stores.
The 1994 Nissan Pathfinder had bolt torque specification is 140 pounds. There is not any removal sequence. There is only a sequence to put the bolts in.
The same 5.0L Windsor V8 was used in the 1992 F-series pickups and made 185 Horse Power at the crank and 270 lb-ft of torque.
Give me food and I will live give me water and I will die what am I?
What is 8 divided by 2(2 plus 2)?
What is the closest us capital to Canada?
Who was Hillary Clintons running mate in the 2008 presidential elections?
Easiest way to lose lower stomach fat?
What is the prefix of done?
Baseball players with 3000 hits 300 home runs and a 300 batting average?
Which is bigger 0.3 or 0.25?
Can you get sunburned in the shade?
What are the dog days of summer?
What is the toughest academic course according to the Guinness Book of World Records 2011?
Why do so many foods "taste like chicken"?
Who invented Lincoln Logs?
How did chickenpox get its name?
What is doomscrolling?
How did the Wiffle Ball get its name?
What investment is necessary for a yield of 500 dollars per month at 6 percent interest?
When two pieces of cui or other unclassified information are posted online together?
How do you transulate happy independence day in konkani language?
How many ODD DAYS IN DECADE?
Ano ang mga salik sa pagkakaroon ng Bilinggwalismo?
What is the meaning of the poem TO A LOVELY WOMAN To A Lovely Woman Angela Manalang-Gloria Shall I compare you to a rainbowed shower Drawing to earth the very arc of dream Or shall I say you are an or?
Ano ang pagkakapareho ng panitikan at kasaysayan?
WHAT IS THE EXPECTATION ON THE SUBJECT NSTP AND TO THE INSTRUCTOR AND CLASSMATE?
Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.