answersLogoWhite
Head Gaskets and Valve Covers
Dodge Ram
Grand Prix SE
Classic 1964-1978 Ford Mustangs

What is the torque on the head bolts for a 1966 mustang 200Ci 6 cylinder?

171819

Top Answer
User Avatar
Wiki User
Answered 2007-06-06 01:42:03

Torque on the Ford 200 c.i. L6 head bolts is 60-65 ft/lbs. Apply torque in a three-step process to acheive the correct final torque (i.e. 45/55/65). The 200 L6 (inline six) engine was used in a variety of Ford cars from 1962 thru 1983 including Falcon, Mustang, and Maverick to name a few.

012
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Your Answer

Related Questions


torque for 2c engine cylinder head bolts


torque setting for cylinder head bolts for a skoda felicia


The torque specs for a Toyota Camry cylinder head is 60 pounds for the inside bolts and 50 pounds for the site bolts. The cylinder head bolts should be tight from and to end alternating.


The following is taken from the Ford shop manual concerning the 1967 Mustang: Torque limits for cylinder head bolts, 170 and 200 CID engines: Step 1: 55 Step 2: 65 Step 3: 70-75


torque settings for cylinder head bolts



what are the torque for camshaft and cylinder head bolts please


The cylinder head bolt torque specification is 90 pounds. The cylinder head bolts should be torqued in 30 pound intervals.


What are the torque specifications and the tightening sequence of the cylinder head bolts on a 1996 Saturn SL1?


Cylinder head to block torque = 80 ft-lbs.


The only reference my manual has to exhaust manifold bolts says to tighten them and bend the locking tabs over.


The cylinder head on a Toyota Paseo requires 33 pounds of torque on the head bolts. If the bolts are over tighten the block can warp leading to a blown head gasket.


The cylinder had bolt torque specification is 90 pounds. The cylinder head bolts should be torqued in 30 pound intervals.


M10 main bolts 45Nm, M6 chain duct bolts 12Nm


Tighten the cylinder head bolts in three steps using the sequence provided : ==== ==== # Step 1- Snug tighten M12 cylinder head bolts, in sequence, to 34 N·m (25 ft. lbs.) and M8 bolts to 20 N·m (15 ft. lbs.) torque. # Step 2- Tighten M12 cylinder head bolts, in sequence, to 54 N·m (40 ft. lbs.) and verify M8 bolts to 20 N·m (15 ft. lbs.) torque. # Step 3- Turn M12 cylinder head bolts, in sequence, 90 degrees and tighten M8 bolts to 34 N·m (25 ft. lbs.) torque.



hi i am looking for the torque settings for a proton gen 2 cylinder head bolt and crank shaft bolts both big ends and main bearing bolts


The 2002 Cavalier 2.2 liter engine cylinder head bolt torque specification is 120 pounds. The cylinder head bolts should be torqued in 40 pound intervals.


Hello: Install cylinder head bolts. Tighten cylinder head bolts according to following procedure: Tighten cylinder head bolts in order shown, Can not show diagram for this. Tightening torque : 36.1 lb-ft (49N


Get a manual on your car and it will give you the settings of the intake, exhaust bolts plus the head bolts and torque pattern.


The cylinder head torque on a 2000 Honda Civic is set at two different rates. For placing the head correctly the bolts need to be tighten to 22 ft torque. Once correctly set the bolts will need 49 ft torque to be properly tighten.


maruti 800 2002 tightening torques of cylinder head


i have a 4d32 deisel engine i change the cylinder gaskit i need to know how much foot pound to torque the bolts


the head bolts are tightenend to spec in 2-3 steps and go from 18-37


http://wiki.answers.com/Q/What_are_the_torque_settingsand_tightening_sequence_for_the_cylinder_head_bolts_on_a_kia_sedona_2.9 the cylinder head bolts on a kia sedona 2.9?"



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.