Asked in Honda Civic CX
Honda Civic CX
What is the torque on the rear bolts of a camber arm for a 1997 civic?
We need you to answer this question!
If you know the answer to this question, please register to join our limited beta program and start the conversation right now!
What is the cylinder head torque sequence for a 1997 ford escort 2.0l?
torque head bolts and order ford 1997 2.0L picture if avalible please
Asked in Chevy Lumina, Chevy Malibu, Grand Prix SE
What are the head bolt torque specs for a 1995 Pontiac 3.1 liter head bolts?
What is the head bolt torque for a 1997 chevy lumina four cylinder?
Location of Idle Air Control valve on a 1997 Honda civic?
Behind the intake manifold facing the firewall. It is held on by three 12mm bolts. I have a 1997 Civic DX 5 spd and it looks like the IACV is on the throttle body facing the engine. This IAVC has 4 bolts or screws. Its very difficult to get to. ...
Asked in Honda Accord
What is the torque spec on the front disc brake caliper bolts 1997 Honda Accord?
According to the 1994-1997 Honda Accord Service Manual the torque specs are: 74 N.m (7.5 kgf.m. 54 Ibf.ft) ...
What are the torque values for the cylinder head of a 1997 24L Pontiac Grand Am?
For all the 2.3, 2.4L QUAD 4 engines, the head bolts are Torque to Yield. The porper torque value is 30ftlbs PLUS a 90 degree turn of the wrench. The bolts must be new every time ( NEVER REUSE OLD BOLTS). The torque values and proper sequence are including in the box the new bolts come with. BUT honestly, the torque value is 65ft lbs like all GM Chevy motors have been for eons. ...
Asked in Dodge Dakota
Cylindear heads torque Dodge Dakota 1997?
4 cylinder: Bolt 7 is on the front driver's corner. # Tighten all bolts in sequence (1 through 10) to 30 NÂ·m (22 ft. lbs.) torque. # Tighten all bolts in sequence (1 through 10) to 61 NÂ·m (45 ft. lbs.) torque. # Check all bolts to verify they are set to 61 NÂ·m (45 ft. lbs.) torque. # Tighten bolts (in sequence): # Bolts 1 through 6 to 149 NÂ·m (110 ft. lbs.) torque. * Bolt 7 to 136 NÂ·m...
Asked in Ford Ranger, Ford Ranger XLT
What is the torque on the bolts for shock absorbers on a 1997 ford ranger?
Ford recommends that you turn the bolt sideways and tighten with your fingers until they hurt. ...
Asked in Chevy Camaro
What is the head torque spec on a 1997 Chevy Camaro LT1?
first you tighten them all to 22 in-lbs, then the short bolts get turned an additional 67 degrees and the medium length to long bolts an additional 80 degrees. ...
Asked in Honda Civic
How do you remove the passenger quarter panel on a 1997 Honda Civic?
The front passenger quarter panel on a 1997 Honda Civic is taken off by removing all of the mounting hardware. Lift the hood and locate all the mounting bolts on the inside is remove them. Check under the vehicles for dust coves and remove them. Open the door and remove the bolts. Once all mounting hardware is removed pull the fender off. ...
Asked in Chevy Silverado, Dodge Ram, Oldsmobile Bravada
What are the torque settings for the bolts on a 1997 Oldsmobile Bravada water pump?
I am not sure of the exact settings, but this site which allows you to identify torque settings through thread and size etc. may help. http://www.mechanical-fitter.co.uk/torque.htm. ...
What is the torque setting for a 416 rover twin ohc head bolts 1997?
Engine code K16-1.6 Head torque Stage 1. 20Nm Stage 2. + 180 degrees Stage 3. + 180 degrees. ...
What are the torque specs for heads and intake on 1997 3100 series 3.1 liter V6?
3100 Vin M apply high temp sealant Rtv to threds and under head bolts ( step one head bolts 37 ft lbs) (step 2 then 1/4 turn) lower intake torque four long bolts at step 1( 66 inch step 2( 10 ft lbs then the outer bolts right then left install upper intake and torque all 14 lb from center out do not under torque or over torque and make sure you have a accurate torque wrench not one that has been threw...