answersLogoWhite
Vauxhall
Ford F-150
Classic 1964-1978 Ford Mustangs
Hand Tools

What is the torque settings for a Vauxhall Cavalier 2.0 8 valve ne engine big end bearings?

606162

Top Answer
User Avatar
Wiki User
2006-04-09 19:19:25
2006-04-09 19:19:25

New bolts required,they are "use once"stretch bolt.Also,an angle gauge is required,or you can make one from card. Torque to 35Nm + 45 degrees + 15 degrees.

1

Related Questions

User Avatar

Wheel bearings? Axle bearings? Differential carrier bearings? Engine main bearings? Engine rod bearings? Engine cam bearings? Need more info to help you.

User Avatar

You need to specify which torque settings. As with any vehicle, torque settings are specific to a particular part of the vehicle.The torque settings for the cylinder head will differ from the settings for the crankshaft bearings.

User Avatar

roller bearings are only needed if engine has roller bearings, u would replace bearings with same bearings that are in engine and cam specs

User Avatar

will 2001 2.2 cavalier interchange engine parts with a 2000 cavalier

User Avatar

It all depends on the bearings that you need to replace! Get some quotes! If it is bearings inside the engine, then the mechanic you go to is going to have pull the engine anyways, so if there are no other problem with your engine but some bearings then i would just have the bearing replaced, but if you have other problems due to the bearings going out, then i would replace the engine. Hope i helped

User Avatar

The 98 Cavalier 2.4 is a NON interference engine.

User Avatar

engine bearings failed . do not run engine until bearings have been replaced. (note) count the bearings that came out in the oil and compare that number to the number on your new bearings. any bearings left in the engine can become failed with other parts and harm the engine. Some times, magnets will placed into oil filters.

User Avatar

I replaced my 1995 S10 2.2 engine with a 2.2 cavalier engine and it worked fine.

User Avatar

The airbag ECU on a Vauxhall Vectra is located in the engine bay. It is on the side of the engine on the passenger side.

User Avatar

vauxhall vectra 2.2 z22se engine has a chain

User Avatar

u need a torque rench with your injector torque settings, they are on the side of the head built in in the 2.5 tds isuzu engine

User Avatar

Depends on the vehicle and which bearings. Wheel bearings, not so expensive. Main bearings inside the engine, expensive.

User Avatar

Why are ets and engine light on in 98 Chevy cavalier

User Avatar

The air filter on a 1998 Vauxhall Corsa engine is located in the engine bay. It is located at the rear of the compartment.

User Avatar

This depends on what bearings in what make model year and engine of car.

User Avatar

The Vauxhall corsa engine layout is North-South, Mid-Engine Transverse, Rear-Mounted, Front Transverse and there are some consumers that have a preference.

User Avatar

Where is engine number on 2007 vivaro

User Avatar

You can swap the engine from your 1997 Cavalier 2.2 liter engine to your 2000 Chevy Cavalier. The wiring harness and motor mounts should be in exactly the same.

User Avatar

No...No....No... The 2.2L OHV engine and the 2.4L DOHC (Quad-4) engine are two different animals.

User Avatar

piston pin, piston rings, side bearings, connecting rod bearings

User Avatar

The Chevrolet Cavalier 2.2 liter engine will fit into a Chevrolet S 10 pickup. You will need to change the motor mounts on the Cavalier engine in order for the engine to bolt in properly.

User Avatar

Specs for main bearings on a 2003 Chevy trailblazer with 4.2 engine .


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.