answersLogoWhite

0


Best Answer

that my friend would be a t45 or a t50 dont know why they use 2 different sizes. But mine was the t50 but the mechanic that I talked to said that there are also ones that use the t45. its actually a t47 its a perfect very tight fit although its a very rare and special size you will probably have to order it as i did Autozone sells torques bit sets with the size needed and a torques size tester (not sure if name is correct), it is many red plastic pieces on a key ring and checks normal torques as well as internal torques sizes.

User Avatar

Wiki User

โˆ™ 2008-01-19 20:56:03
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: What is the torx bolt size on a 1985 celebritys front brakes?
Write your answer...
Submit
Related questions

How Adjust rear brakes 1985 Toyota Tercel?

The 1985 Toyota Tercel brakes are equipped with an adjustment bolt. Turn the adjustment bolt to raise or lower the brake shoe.


What are torque specs for Chevy Venture front brakes?

bolt torques for front callipers slide and mounting


What size wrench for caliper bolt on front brakes?

Type and year of car would help.


What tools are needed to change brakes on a 1995 Isuzu rodeo?

14 mm wrench or socket--top bolt does not loosen--take out bottom bolt and snap out pads -- front and back of each wheel


How do you change the front brakes of your 90 jetta if the bolts have been warped?

pull back the ruber around the bolt and use a pair of vise grips.


What tool do you need to remove the bolt from the caliper on a 99 Taurus front disc brakes Is it a star or hex bit?

It is either a T-40 or a T-45 Torx.


What size Allen wrench do you use to change front brakes on a 2000 cougar?

You need a torx type socket. If you use an Allen wrench...you will strip out the inside of the bolt.


Can you change drum brakes on a 62 Chevy impala to disc brakes?

Yes. There are manysuppliers of aftermarket bolt-on kits.


1990 VW Jetta - on the front right brake caliper is one bolt that holds the caliper on supposed to be longer than the other?

I did my jetta brakes many times, but I dont recall the bolt lengths. Ensure you have adequate engagement into nut. The dealer can supply you with the proper bolt for about 4 bucks.


What is the bolt pattern for a 1985 GMC Sierra Classic?

Bolt pattern for a 1985 GMC Sierra Classic 1500 is 6x5.5 (That is what mine is)


How do you replace front brakes on a 2000 Saturn SC?

This is how you will replace the front brakes on a 2000 Saturn Sc first you will jack the car up with jack stands. You will then remove the front wheels, next remove the upper caliper to mount bolt only. Then you will pivot the caliper downward to access the pads, you will remove the old pads and install the new pads. You will use a 'C' clamp and a old pad to bottom the caliper piston and you will pivot the caliper back into place and re-install the bolt.


Where is the oil drain plug on a 1985 Yamaha FJ600?

look at the below the oil filter. It is a 19mm bolt that faces the front tire. in the center of the bolt it looks like there is a Phillips screw. The bolt is underneath the engine block between the exhaust pipes. good luck!


How do you change front disc brakes on a 2002 Mazda B-3000 pickup?

Im not 100%, but when i have changed other brakes like those in the past there was and Alan wrench bolt towards the inside of the truck, just take take that out and u should be able to figure it out from there, im not sure but i think you can just take them off by removeing that bolt but their might be something else you have to do...


What is the torque spec for front center bolt?

97 buick lesabre center front wheel bolt size


What is the bolt pattern for 85 El Camino?

what is the bolt pattern for 1985 el camino


Brake adjustment John Deere LX173?

There is a bolt near the rear of the mower that faces the rear right wheel. If you can press the brake while looking by the rear wheel, you'll be able to see where the bolt is. It is toward the top, front of the the right rear wheel. All you have to do is tighten the bolt a little and you'll have brakes again.


Bottom bolt on front brake bolt will not move in and out to get brakes back on?

Sounds like the sliders are frozen, u may be able to get them apart, if u can try and clean them and put fresh hi temp disc break grease, if there really bad i would replace them.


What is bolt pattern diameter for 1985 s10?

1985 Chevy s10 RWD on 14' factory wheels bolt pattern is 5x4.75 (5x4 3/4) .


What does it mean when you replace new brakes and they still make scrubbing sound?

did u bleed the brakes as u tighten up the( pin ) bolt .


Where are the set bolt pivot bolt and tensioning bolt on an 1985 jetta power steering pump located?

www.kiss my bolty pivot ass.com


Will 1985 Chevy truck front clip fit a 1980 GMC truck?

Yes, they will bolt up. If I remember correctly, from 73-87 was pretty much the same truck.


How do you replace rear disc brake pads on 87 Fiero GT?

The same way you replace the front. there both disc brakes all you do is take the caliper bolts out if there factory it'll be star head bolt ifs its aftermarkret they'll be Allen heads just remove the caliper and replace the brakes


How to adjust brakes on a john deere lt150?

You'll need a 1/2 wrench. On the right side of the transmission, behind the right rear tire there is a bolt in the center of the caliper. Tighten the bolt one quarter turn at a time until you have brakes.


How do you adjust rear brakes on a 2004 Chevrolet Aveo?

You can adjust the rear brakes with the rear brake adjustment bolt. The rear brakes should adjust automatically every time you back up and use the brake.


I can not get the bolt loosend in the front Do you take to bolt out from the bottom or the top?

With out knowing what you are working on we can not help.