Head Gaskets and Valve Covers
Ford Ranger
Ford Ranger XLT

What is the typical torque pounds on V6 Ford Ranger heads around 1984?

404142

Top Answer
User Avatar
Wiki User
2006-04-02 19:09:13
2006-04-02 19:09:13

3litre- step 1 59lbs, step 2 loosen one full turn, step 3 37lbs , step 4 68lbs 4litre- step 1 44lbs ,step 2 tighten manifold intake bolts to 36 then to 72 in-lbs. step 3 head bolts to 59 lbs . step 4 tighten intake bolts to 72 then to 132 in lbs. step 5 tighten head bolts another 80 to 85 degrees.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The Ford Ranger alternator bolt torque specification is dependent upon the year of the Ford Ranger. In general, the alternator bolt torque specification is 45 pounds.

User Avatar

The 1999 Ford Ranger 3.0 liter water pump bolt torque specifications are 40 pounds. You do not want to torque the bolts to hard or they will break.

User Avatar

A typical car's maintenance manual will quote at least 60 Torque settings. My Taurus manual has 74 torque settings. -The Ranger ( being 4WD ) will have at least 90 . - Do you seriously expect us to quote them all - -

User Avatar

Around 80-85 pounds of torque.

User Avatar

I believe it is 140 H.P. at 4600 RPM and 170 foot pounds torque at 2600 RPM

User Avatar

anywhere from 85 pounds torque to 90 pounds torque will work, but factory is 87 pounds torque. personnally, i set mine at 100 pounds torque

User Avatar

The 2002 Ranger - 3.0 L - is rated at 146 horsepower @5050 RPM and 180 foot pounds torque @ 3500 RPM

User Avatar

22 ft pounds then 52 ft pounds, then another 90 degrees Both head gaskets are NOT the same!

User Avatar

What is the Torque setting on transmission pan bolts 2002 ford ranger?

User Avatar

torque spec on the oil drain plug on a 2.9 ford ranger?

User Avatar

Model Year and engine type may be critical information. From AutoZone.com's Repair Section; here is a typical Ford 3.0L application. You can check there for other engines as well. your 1998 Ford Truck Ranger 2WD (3.0L MFI): Foot pounds (Final torque) Note: Torque sequence ------------ front | 6 4 2 8 | | 5 1 3 7 | ------------ Step 1: torque in sequence to 59 Ft/Lbs Step 2: loosen all bolts in sequence (1) full turn Step 3: torque in sequence to 40 Ft/Lbs Step 4: torque in sequence to 73 Ft/Lbs recheck final torque in sequence

User Avatar

i'm looking for the torque specs on the rocker arms on a 1999 ford ranger 3.0 v6 the torque is 18-26 lbs

User Avatar

90 inch - pounds (torque) = 90 / 12 = 7.5 foot pounds (torque)

User Avatar

first torque to 60 ftlbs then torque to 90 ftlbs

User Avatar

What are the torque specs for 99 ford ranger 3.0L intake manifold?

User Avatar

what is the torque setting for big ends and main bearing on a 2.5tdi ford ranger

User Avatar

The Polaris Sportsmen 800 has 120 pounds of engine torque. The torque is measured at the flywheel. There is only 100 pounds of torque at the ground.

User Avatar

You need six pounds of pressure to torque.

User Avatar

Torque settings on 1300 Toyota Tazz are torque to 59 foot-pounds, loosen one full-turn. Then, torque 37 foot-pounds and 68 foot-pounds. Torque sequence is 6, 4, 2, 8,7, 3, 1, 5.

User Avatar

140 horsepower @ 4600 RPM / 170 foot pounds torque @ 2600 RPM

User Avatar

454 engine torque is 752 pounds of torque

User Avatar

The torque specs for a Cadillac depend on which engine it has. For most 425, 572, 368, and 500 engines, the torque for the head bolts is 115 ft. pounds. The torque for the cam bolts is 25 ft. pounds, and the torque for the valve covers is 10 ft. pounds.

User Avatar

Torque is measured in foot pounds, and the abbreviation is an association. Also newtons per meter is the metric equivalent. So TORQUE!


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.