0.3v as opposed to the silicon 0.6v
about 0.2 V more at higher temps any closer look at the specific diodes spec sheet dopeants vary
97f
The silicon diode (unless its a Schottky diode) conducts at approximately 0.6 volts. The germanium diode, however, conducts at a much lower voltage, typically 0.2 volts. This means that the germanium diode is better at small signal rectification applications, such as AM radio detectors, allowing a smaller tuner tank circuit.
A silicon diode has a voltage drop of approximately 0.7V, while a germanium diode has a voltage drop of approximately 0.3V. Though germanium diodes are better in the area of forward voltage drop, silicon diodes are cheaper to produce and have higher breakdown voltages and current capabilities.
To forward bias a germanium diode you need to reach between 0.2 and 0.3 V between anode (+) and cathode (-). Once this voltage is reached, the diode will conduct. Make sure you have a resistor to limit the forward current to a safe (for the diode, that is) value.
Potential barrier of silicon is 0.7, whereas potential barrier of germanium is 0.3
Forward biase the given diode by using a Variable resistor in the circuit. By adjusting the value of variable resistor you will adjust the voltage being applied to junction diode. First adjust the resistance such that no(negligble) current flows through the circuit. Now start decreasing the value of resistance. Note the voltage across resistor(Vr) when current just starts flowing through the circuit. Then Potential barrier of diode will be: Vb=V-Vr Vb:Barrier Potential V:Battery Voltage Vr:Voltage Drop across resistance when current just starts flowing through the circuit.
There is no exact substitute for a germanium diode, except another germanium diode. However if the only concern is to get a lower forward voltage drop than that of a silicon diode (0.7V), then a schottky barrier diode may be a suitable replacement as its forward voltage drop (<0.1V) is even lower than that of a germanium diode (0.2V).
about 0.2 V more at higher temps any closer look at the specific diodes spec sheet dopeants vary
The potential barrier of a diode is caused by the movement of electrons to create holes. The electrons and holes create a potential barrier, but as this voltage will not supply current, it cannot be used as a voltage source.
cut in voltage *** for silicon is 0.7volts and that for germanium is 0.3volts.According to Millman and Taub, "Pulse, Digital and Switching Waveforms", McGraw-Hill 1965, the cutin (or offset, break-point or threshold) voltage for a silicon diode is 0.6, and 0.2 for germanium.Breakdown voltage is another thing entirely. It is the reverse voltage at which the junction will break down.
Cut in voltage is the minimum voltage required to overcome the barrier potential. In other words it is like trying to push a large boulder....it may not be possible to push a large boulder by one person but it may be done if 2 or more people try to push it together depending on the size of the boulder.....similarly....the charge carriers in the barrier region have a potential energy of about 0.6V for Silicon and about 0.2V for Germanium. so in order for the diode to conduct, it is required to overcome the potential of the charge carriers in the junction barrier region and hence only if a potential more than that of the barrier potential (cut off voltage) is applied, then electrons flow past the junction barrier and the diode conducts.
The barrier voltage of a diode is 0.7v for silicon and 0.3 for germanium. after this voltage is reached the current starts increasing rapidly... till this voltage is reached the current increases in very small steps...
Negitive cathode, positive anode, voltage accross barrier = 0.3V
97f
silicon diode is preferred more when compared with germanium diode because in silicon diode the operating voltage is 0.7v where as in germanium diode the operating voltage is 0.3v , germanium is temperature sensitive so it can be easily destroyed by increasing temperature hence silicon diode is preferred more
In general O in diodes stands for germanium.since OA79 is a germanium diode O stands for germanium