answersLogoWhite

0


Top Answer
User Avatar
Wiki User
Answered 2004-10-05 00:09:30

Sometimes U can use a 90? pair of needle nose pliers or U can pull off the 2 small bolts holding the plate on-then take thick grease & put on the shaft & install the pump FAST or there is a bolt INFRONT of the engine that goes through 2 that rod-take out the short bolt & install a longer bolt(3/8 corse thread) 2 slightly put pressure on the FALLING out rod.Sometimes U need 2 put a taper on the longer bolt(JUST ON THE END) 2 hold the rod in place.then REINSTALL the ORIGINAL bolt BEFORE U START THE ENGINE.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

Is rtv sealant necessary when replacing intake manifold gasket in 1994 Chevy 5.7 350 engine?

You need the sealant on the ends where the supplied gaskets don't cover fully.


How do you fix AC Heater control unit on 1992 Chevy pickup?

They are fully electronic. If you're sure it's the controls, you'll have to buy a new one from the dealer or a used one from an auto wrecker.


What year did the first Chevy Silverado come out?

This is a Question???& Possible answer I know that the Chevy Silverado also came out in the 60's as my Dad had one bout it brand new In CA. Come on Guys come up with the right date on this It was a ton Pickup fully Loaded.


How do you unlock a fully retracted drivers seat belt on a Chevy 2004 tracker?

Fully retracted or fully extended, the mechanism must be broken. Replace it with a new or good used one.


How much does a fully loaded pickup truck weigh?

Not enough info to answer that question. The year, make and model info needed.


Why synonyms important in communication?

Synonyms are important in communication because if the person you are communicating with does not fully understand the meaning of a certain word, a synonym can be helpful in replacing that word with one they better understand. Example: If someone does not fully understand the word " benevolent", replacing it with the word "nice" could help he or she understand you.


Rattling brakes on 1996 Chevy pickup?

If you front brakes rattle, it is usually caused by a a stuck puck or piston in your brake assembly. When this happens, the piston does not fully retract at times causing you brake pad or pads to wear excessibly and when the piston finally retracts fully and does not keep constant pressure on your pads you get a rattle. I had this problem on my F-150 and the brake guy solved this by installing steel pucks and lube.


Why wont a 1995 engine work in a 1991 Nissan pickup?

The 1995 engine is fully electronic, while the 1991 engine is primarily mechanical.


What are the specifications of Chevy Crate Engines?

Specifications for Chevy Crate Engines are client specific and to the order. You have several options in having the engine fully or even partially built.


What would cause a 1997 Grand Am GT not to start after replacing the alternator?

is your battery in good condition and fully charged? is your starter good?


Does uniformed have a prefix?

the word uniformed does have a prefix, -un. un means not, to fully understand try replacing the prefix with the definition, not Informed.


Can replacing air filter cause the air fuel sensor heater circuit response to malfunction?

No but make sure your ar filter box is fully closed after replacing and make sure that ho2 sensor is working good


Can you emancipate a disabled child?

That is fully dependent of the decision of the court and the interpretation of the evidence behind the motion.


Can a 4 year old sit in the front of a pickup?

A four year old can NOT sit in the front of any vehicle not to mention a pickup truck. If a four year old was in the front seat of a pickup and you crashed the air bag will deploy. Air bags can break the ribs of a fully developed adult, imagine what it can do to a four year old! Please, DO NOT LET YOUR FOUR YEAR OLD, OR ANY CHILD WHO HAS NOT FULLY DEVELOPED YET SIT IN THE FRONT OF ANY VEHICLE. Yours Truly, Anonymous


What is the best American pickup truck?

That's a subjective question, what's best to one person is not to another. I would suggest you read some reviews and do some test drives. All the full size trucks are pretty similar. Only way to know what American Pickup is best to you is to do a comparison and test drive them. Best pick truck to and for me is the Chevy Silverado 1500 Crew Cab Fully Loaded. See, the trucks we think is the best might not be best to you.


Why would your car not accelerate over 20 mph after replacing the carborator?

The throttle cable could possibly be problem (not opening the butterfly valve fully).With the engine switched off, let someone fully depress the accelerator pedal while you look into the carburettor to see if the valve is fully open.


How do you tighten the emergency brake on a 1986 Toyota pickup?

Look underneath on the passenger side just behind the cab. There is a bracket that you can adjust to tighten it up. If its adjusted as tight as it can be, but still wont fully engage, you prob need rear brake work done. Look underneath on the passenger side just behind the cab. There is a bracket that you can adjust to tighten it up. If its adjusted as tight as it can be, but still wont fully engage, you prob need rear brake work done. Look underneath on the passenger side just behind the cab. There is a bracket that you can adjust to tighten it up. If its adjusted as tight as it can be, but still wont fully engage, you prob need rear brake work done. Look underneath on the passenger side just behind the cab. There is a bracket that you can adjust to tighten it up. If its adjusted as tight as it can be, but still wont fully engage, you prob need rear brake work done. Look underneath on the passenger side just behind the cab. There is a bracket that you can adjust to tighten it up. If its adjusted as tight as it can be, but still wont fully engage, you prob need rear brake work done. Look underneath on the passenger side just behind the cab. There is a bracket that you can adjust to tighten it up. If its adjusted as tight as it can be, but still wont fully engage, you prob need rear brake work done.


What is wrong if a 1988 Chevy pickup starter will not fire up and there is only a faint click from behind the dash and the hot wire to the starter is tight as are battery terminals?

assuming the batt.is fully charged,it may be the solenoid not engaging the starter motor.you can remove the starter motor and solenoid and run jumper wires to it .if starter does not spin,it may be the solenoid not engaging the starter.keep hands and clothing away from starter when doing this test!also,you did not mention if the solenoid wire was fastened to starter when you replaced it.usually purple color on chevy.good luck


How do determine if you have a short be or long bed on your 1991 Toyota pickup?

i believe the long bed is fully 8'0" inside, whereas the short bed is approx 6'0"


How much does a small block Chevy head weigh?

I just weighed a 327 fully assembled head at 45 lbs.


Does the 1990 Mazda b2600I pickup truck have a non-locking rear wheel?

The SE-5 package has a limited slip differential but it doesn't fully lock.


What is a new moon and a full moon's appearance?

You can't see a new moon at all because the sun is behind it and the side we are looking at is not lit up. A full moon can be seen as a fully illuminated circle because the sun is behind us, shining fully on the part of the moon facing us.


Is the Chevy Volt car fully electic?

No. There are actually no all electric cars yet. Chevy, GM, cars Ford are all in the process of finding new ways to make all electric cars.


Why don't you get heat when the temperature control on your Chevy S10 is in the fully clockwise position?

try replacing the thermostat for $8... if that doesnt work check your coolant level.. if its always low you prob need to replace the manafold gasket, which is cheap to buy but expencive for a garage to put in if you dont know how to do it yourself. If your asking this question you prob. dont know how.


What happens when small block Chevy rocker arm is set to tight?

The valves won't be able to fully close at higher rpm.