Cars & Vehicles
Ford E-250 Van
Ford F-250
Turn Signals and Hazard Lights

What is wrong with a 98 ford econoline 250 if when you put on the turn signal both turn signals stay on solid instead of blinking all the bulbs have been checked and they all work fine?

678

Top Answer
User Avatar
Wiki User
2005-09-22 01:19:10
2005-09-22 01:19:10

look in your fuse panel and find the 1 1/4 inch diameter aluminum gizmo and replace it ($3/$4).It's a flasher.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

There are two relays, one for the emergency flasher and one for the turn signals. Replace the Flasher Relay for the turn signals, it is defective.

User Avatar

I see this a lot on many vehicles it is simply a warning telling you that it is about to burn out. The reason it blinks faster is so that the bulb doesn't too hot for a longer amount of time than it usually does.

User Avatar

Usually, a fast blinking turn signal means one of the outside turn signals (front, back and side) lights is burned out.

User Avatar

Blinking lights on a laptop are a way of sending signals to the users. All of the lights mean different things. For a listing of what the lights mean on your laptop please see the manual that came with the laptop.

User Avatar

check the bulbs first. most of the time a bad bulb will stop them from blinking.

User Avatar

If the vehicle is equipped with a trailer light plug, the wires for the brake lights and the turn signals have been connected together, which is common, as many trailers do not have separate lights for brakes and turn signals.

User Avatar

the red light signals that the pulse is going out through the electrical system.

User Avatar

When I drive, the turn signals work fine when I'm not tilting the steering wheel. So if I were you, I'd get your car checked out.

User Avatar

Turn signals just quit working- have replaced flasher- checked all bulbs and fuses, checked all obvious wires, cleaned grounds, replaced the turn signal switch (that was an adventure). At a loss- any help out there? Hazards work fine- all other lights work fine- turn signals dead

User Avatar

They are called traffic lights or traffic signals. -------------------------------------------------------- *** 2nd Answerer Says: Some parts of the country call them stoplights (as opposed to go-lights or caution-lights) and there is a variation called "blinking lights". "Blinking lights can be blinking red in all four directions to designate a four-way stop or full-stop in two directions & cautionary slow-down (blinking yellow) the other two directions.

User Avatar

The computer that controls the component cannot do what it wants to do so it signals you to give it attention get it diagnosied by an ASE trained experianced tech

User Avatar

i think warning signals mean that something need to be checked on the vehicle, so it would really be an indication that mechanically something is wrong and needs to be checked out

User Avatar

Your turn signals may not be blinking properly because something may be wrong with the wiring or fuses. Take your Harley to an authorized dealer to have diagnostic testing done.

User Avatar

If turn signals are not blinking on the dashboard but they are still working, the cause might be a burned out bulb in one of the blinkers on the outside of the car. There might also be a fuse burned out or bulbs burned out in the dash. Even the flasher can be the problem in this situation.

User Avatar

It could be the turn signal bulbs, some vehicles use separate bulbs for the hazard and turn signals. It could also be a bad switch or wires for the turn signals.

User Avatar

Most of the time when this occurs, it is a sign of a bad ground. Check all the ground connections.

User Avatar

Take your car in to have it checked. Turn signals should work without high beams.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.