Transmissions and Drivetrains
Mercury Grand Marquis
Chevy Blazer S-10

What is wrong with your car if nothing works on the shifting lever including no reverse no park and no forward gears?

525354

Top Answer
User Avatar
Wiki User
2009-12-13 20:34:15
2009-12-13 20:34:15
Answer

Your transmission is probably blown(broken). Probably get a new transmission or try to find a used one with very little miles.

Your linkage to the trans may have become disengaged since you do not have the parking gear either. Check under the car to make sure it is shifting when you shift from inside the vehicle.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

It may not be in all the way, try shifting from reverse to forward a couple times.

User Avatar

This nothing but forward and reverse recording... nothing but bidirectional meters

User Avatar

A car might stall when shifting from park to reverse if the idle is set too low. It is also possible that the engine stalls because it is not fully warmed up before shifting from park to reverse.

User Avatar

Yes, you could severely damage a transmission by shifting into reverse while moving forward. But the odds of the transmission actually going into reverse are not good because there are safety mechanisms in place to prevent it from happening.

User Avatar

Burnt forward clutches/ The forward cluth pack is stuck/welded together.... You need a overhaul...!

User Avatar

has a full charge won't go forward or reverse

User Avatar

Nothing if you are sitting still. However if you are moving forward and it is an older car, you may be replacing a transmission. Most if not all cars today with and automatic trasnmission have a failsafe to prevent going into reverse while going forward.

User Avatar

Yes, if there is only one forward and one reverse reaction.

User Avatar

Difficulty shifting, can't reach first gear and grinds to reverse, have to stomp on the brakes to downshift, basically any sort of unusual difficulty with shifting, car jumps forward when clutch is engaged or moves while on a flat surface and clutch is engaged.

User Avatar

macroscopic characteristics of both forward and reverse reactions

User Avatar

truck will only go forward not in reverse does this mean the transmission is gone

User Avatar

The ammeter is connected in different way in forward and reverse bias zenner diode. So that all of the board will work right going forward and reverse.

User Avatar

chemical equilibrium is where forward and reverse reactions occurs in a same rate or in equal rate....orrate(forward) = rate(reverse)

User Avatar

For chemical equilibrium Rate of forward reaction + Rate of reverse reaction = zero

User Avatar

What would cause the 1995 Nissan Pathfinder not to go in forward or reverse?

User Avatar

forward engineering: the creation of code from models. reverse engineering: the creation of models from code.

User Avatar

The cast of Reverse Forward - 2014 includes: Lisa Emilie Grohndahl Casper Rams

User Avatar

In a chemical system, there are forward and reverse reactions occurring constantly. As the forward reactions progress, the increased amount of products allows for more and more reverse reactions. Once the rate of the forward and reverse reactions are equal, the system is at equilibrium. The forward and reverse reactions continue at equal but opposite rates; however, there are no further changes in the concentration of the products and reactants.

User Avatar

A forward reverse star delta is a two in one motor starter where a motor first runs on star connection and then changed to delta connection after a time which has been set. The motor direction can be changed, whether forward or reverse

User Avatar

A forward biased diode conducts current, while a reverse biased diode does not allow any current to flow.

User Avatar

A reverse idler gear in a manual transmission. It converts the reverse gears turning direction into the outputshaft to reverse its direction. The transmission can not spin clockwise when the reverse idler is engaged thus it only spins backwards not forward.

User Avatar

Most mixers have a so called "phase reverse button" but it's not a "phase" button, it's the "polarity reverse" button in each channel. It's real simple, to reverse the polarity on a mic, you simply reverse the pin wires 2 an 3.Phase means time shifting. Polarity reversion means changing cable a and b.That are really different things.Scroll down to related links and look at "Polarity reversal is not phase shifting".This answer has nothing to do with phase: To reverse the rotation on a three phase motor you simply swap any two of the three motor leads


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.