TO UPGRADE THE HEATING SYSTEM IN CJ'S AFTER 1977 IT IS POSSIBLE TO INSTALL A BLOWER MOTOR FROM A 72-73 Chevy Blazer/PICKUP TRUCK. IT IS A BOLT IN SWAP. THE ONLY THING YOU WILL HAVE TO MODIFY IS THE HOLE IN THE FIREWALL THAT THE BACK OF THE BLOWER MOTOR FITS THROUGH, IT HAS TO BE ENLARGED. HERE IS A WEB ADDRESS THAT DETAILS THE SWAP...http://www.4x4wire.com/Jeep/tech/interior/cjheater
Held in by two screws in a housing just to the left of the blower motor housing.
it on the blower motor housing
The following can cause this problem.................. 1. Bad blower motor. 2. Bad blower motor wheel. 3. Trash in the blower housing...
# Disconnect and isolate the negative battery cable. # Disconnect the wire harness connector from the blower motor . # Release the locking tab that secures the blower motor to the HVAC housing and rotate blower motor counterclockwise. # Rotate and tilt the blower motor as needed for clearance to remove the blower motor and wheel from the HVAC housing. also The blower motor is located on the passenger side of the vehicle under the instrument panel. The blower motor can be removed without having to remove the instrument panel or the HVAC housing.
The blower motor is located on the passenger side of the vehicle under the instrument panel. The blower motor can be removed without having to remove the instrument panel or the HVAC housing.Disconnect and isolate the negative battery cable.Disconnect the wire harness connector from the blower motor .Release the locking tab that secures the blower motor to the HVAC housing and rotate blower motor counterclockwise.Rotate and tilt the blower motor as needed for clearance to remove the blower motor and wheel from the HVAC housing.
The blower motor resister is located just below the blower motor to the left attached to the housing.........
CHECK THE BLOWER HOUSING. IT SITS INSIDE THE HOUSING AND IS SECURED BY SCREWS ON TOP OF THE BLOWER HOUSING.
The blower motor resister is under the passenger side of the dash. It is located in the bottom of the blower housing.
bad blower motor
Remove the instrument panel silencer from the passenger side of the instrument panel. Disconnect the wire harness connector from the blower motor. Remove the three screws that secure the blower motor to the HVAC housing. Remove the blower motor from the HVAC housing by rotating and tilting the motor as needed for clearance of the blower wheel....
It is located on the blower motor housing and is white in color. You have to take the blower motor assembly out as far as I know to get to it.
Fig 15 Blower Motor ResistorNOTE: The blower motor resistor is located on the lower right side of the heater housing.REMOVAL# Remove lower right underpanel silencer/duct. # Disconnect wiring connectors on blower motor resistor. # Remove blower motor resistor retaining screws. # Pull blower motor resistor out of heater housing.
passenger side of engine compartment by the firewall on top of the black housing for the blower motor. 2 screws hold it into the housing
The blower motor on a Mercedes Benz 300e is changed by disconnecting the wiring harness and unbolting the blower from its housing. The motor is then lifted away and a new blower motor connected.
Under the hood to the left of the blower motor mounted in the housing on the firewall...
Inside the blower motor housing directly behind the electrical coupler.
The a/c heater blower motor resister is located in the vehicle on the passengers side inside the housing next to the blower motor...............Remove the blower motor resistor wire harness connector.Remove the blower motor resistor screws.Remove the blower motor resistor.
disconnect the electrical connector from the blower motor and remove the 3 screws from the blower motor housing.pull the blower motor and fan straight down. to remove fan from blower motor,squeeze spring clip togetherand slip fan off the shaft.some models have no clip or screw holding fanto shaft, in this case use 2 screwdrivers to pry it off.install fan onto blower motor housing and install blower motor into the heater housing.
There is only one blower motor resistor and it is located in the evaporator housing.
Disconnect the negative cable from the battery. Unplug the electrical connector. Remove the bolts securingÊthe blower motor housing. Remove the blower motor.
The blower motor is under the pass side dash where your feet would be if you stretch twist the motor to get it out of the housing turn the motor towards the fuse box to get it out once you have it free od the housing good luck
It is usually ( at least on a 2000 Ranger) locted on the blower motor housing in the engine compartment.
The blower motor is inside the bottom of the hvac housing, under the dash on the passenger side.
under the blower motor housing. to the right
How do you replace a defrost blower motor in a 2003 Toyota Corolla