0
What problems would you have when you bolt a razor pro scooter?
Wiki User
∙ 14y ago
Your scooter will start oozing out poop. So i suggest shooting the poop with a uzi to prevent oozing. Hope this helps :)
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you bolt your scooter?
you take a bolt and bolt it.
Is a razor pro stronger than a razor ultra pro?
No. The Razor Ultra Pro is stronger because it is all one piece, unlike the pro model where it folds. not to tick you off or any thing but your wrong and a idiot cuz when you bolt a razor pro it is the strongest scooter on the market! so there :p
Is a Razor a3 a good scooter?
Yes Yes Yes, i have already preordered one, but i have been looking at it on the internet and google and stuff, and i reckon it is alright all you have to do is probaly bolt it and then it is an alright scooter and will be quite stable and strong.is ok
What size bolts do you need to bolt a razor pro?
i bolted my razor pro today. you need to use one 3/8 thick bolt for the top front hole. then you will need two 5/16 thick bolts.put one in the front and the other in the bottom hole.dont forget to buy washers and nuts make sure u have the right size wrenches too. my scooter is now alot more solid and the bars dont move one bit.heres a link of instructions for how to bolt your scooter http://www.inward-scooters.com/uploads/Inward_Scooters_boltset_removal_and_Installation_instructions.pdf
Can you put pegs on a scooter?
yes, you need to find a bolt that is quite long and stick it through the holes on the scooter so that about 5 inches of it is sticking out on the side you want the peg to be on, slide skateboard bearings on the bolt and screw a bolt on the end, there you go, a scooter peg.
Does a suzuki SJ50 scooter have a oil drain bolt?
no
Hopw do you bolt your razor pro model scooter?
dude that's pish posh what you do is take out that middle part near the deck. push it up and slide it out then slide the bolt through and tighten. but if you don't wanna do tat where the white plastic used to be on the squashy bit where the siver thing is find a small enough to fit through then do the same and bolt it.
How do you bolt a razor pro?
Put a bolt through the part near the wheel and hey presto!
Where does the exhaust bolt on to a scooter?
Onto the exhaust port of the engine...
How do you bolt the folding mechanism on regular razor scooter not the razor pro?
ok the easiest way to do this is to drill one hole right on the side in the middle.Before you drill take a screw driver and a hammer and punch a hole [not complete hole] but a dent. Just so you now where drilling at.You need a high powered drill to.Then once you get a hole though it take a front axle from any scooter and us a washer on each side and just tighten it from each sides with the right side alin keys so you dont strip the bolt. My way of doing it is getting a 5.16 bolt and a 3. bolt both with a nut. They are both about 2 inches long. Then, take off your headtube on the scooter and remove everything from the folding mechansim. Put the headtube back on and but the 5.16 bolt in the bottom hole and the 3.8 in the top hole. Get a socket wrench and tighten it as hard as you can so it doesnt rebreak.
How do you bolt a scooter?
their are several videos out on youtube on how to bolt a scooter. firstly its going to depend on what scooter you are trying to bolt. if your going to bolt a razor pro, all you need to do is take out everything that has to do with the folding mech. Then put an 8mm bolt through the bottom most front hole, do not tighten it all the way. Put a 10mm bolt through the slot above that one. before you do it up, take the squaired bolt thingy and put it above the bolt so that it doesn't slide out. next take another 8mm and put it through the rails behind the head tube. after you do that, it should be decently solid, but to make it even more solid your going to have to tighen the head set. in order to do that, you will need to tighten the round part a little bit tighter than what you want it then loosen it as you tighten the bolt over top of it. Sorry if this is confusing but their are videos on youtube explaining each of these things.
How do you install an exhaust pipe on to a 36cc gas scooter?
bolt it on the motor
