answersLogoWhite

0


Top Answer
User Avatar
Wiki User
Answered 2007-03-01 13:05:09

there is not much to changing a brake line u disconnect at both ends. then following where old was routed, u install new one making sure it is not rubbing any where it will rub a hole or get squashed when installed you then need to bleed whole brake system to remove air from lines

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

How do you bleed the brake line after changing the brake pads in a ford mustang?

If you have not opened the brake system ie. taken off any lines or lost any fluid, you should not have to bleed a brake system. Brake jobs are best done by experienced technicians.


What would cause a 1987 Honda Accord front driver side brake not to work after already changing the caliber and brake pad?

There could be many reasons. Did you do the work yourself? If not, take your car back to the shop. If so, did you remember to bleed the brakes? Air bubbles in the brake line could be the problem...


Chevy Venture brake line leaking?

When a brake line is leaking on the Chevy Venture the brake line should be replaced as soon as possible. A leak, however small, can cause hydraulic fluid to escape the brake line which will cause a loss in brake pressure. The brakes should be bled of air after the new line is put in to remove gaps in brake pedal pressure.


How can you fix a brake fluid leak when it's a leak in the brake line?

depends where the leak is. In the brake line or at the pump? electric or mech brakes? if its in the line you should be able to replace the line section


Can you get the vacuum line diagram for a 1988 Honda accord lx?

look under your hook there should be one ....


What causes your brake peddle to go to the floor with out stopping?

A leak in your brake line, or very low brake fluid, both of which are extremely dangerous and should be fixed at once.


How Do you unlock A locked Passenger side rear brake In a 95 gti?

Ok so i figured this one out on my own. Remove the rear tire that the brake is locked up on, if the hand brake is on, lower the lever in the car. locate the e-brake wire on the rear of the disk brake/caliper. This should be behind the rotor and caliber and is identifible by the fact that it is not a hydraulic line. You should see that it is held in place by a bracket with tension on it, hence why the brake is "locked" remove the bracket holding in the brake line in place {not the hydraulic line!!} Once the bracket is removed simple pull out the e-brake line with a pair of pliers, Shazam! the brake should release. If not a few light taps with a hammer should help. Save the bracket for the e-brake as you will need it if you ever decide to fix it. This is a temporay fix with no real long term affects to your braking system, Except the fact that you will only have one E brake working.


Are Acura and Accord the same vehicle?

No, the Acura lineup is not mirrored by the Honda line up. The Honda Accord does not have a "sibling" in the Acura line.


How do you repair brake lines on a 1994 Acura Integra?

Before repairing the brake lines the brake fluid must be drained. The car should be safely lifted and supported. With the wheels off unbolt the line from the caliper to the hardline. Replace the line.


Does changing the power steering line influence the alignment?

Changing power steering fluid lines in your vehicle should not affect alignment.


How do you fix a broken brake line in a 1999 GMC Sierra?

Replace the brake line, bleed the brake. top up with brake fluid. Done.


Changing the front brakes on a 1997 mazada 626 do i have to pull the entire caliper off?

you have to unbolt the caliper off the rotor, but not from the brake fluid line.


Why is my Offside rear brake recording little or no effort?

Air in the brake lines. Severly worn break pads. Worn brake boost piston. Cracked brake line on that brake. Loose brake line.


How do you bleed the brakes after replacing brake pads and fluid On a 1996 Honda Accord?

you need to have some one in the car to pump the brakes till thay get hard. and win they do you crake the bleder open on the brake calaper.the brake will go to the floor then you titan the bleder. and repeat thia over till the brake flouid comes out and there is no more air in the line.


How long does it take for the air to flow through the lines to the brake after the brake pedal is pushed?

Typically brake systems in cars and pickups have brake fluid, not air in the lines. There should never be air in your automotive break line


If everytime you drive a 1990 Honda Civic station wagon a mile the passenger side front brake freezes up and you stop and bleed it and it lets go what is wrong?

Check for a pinched brake line. If the line has been pinched and you use the brakes, the pinched line will hold pressure and not release the brake fluid like it should. That will cause the brake to overheat (it's like driving with the brake on) and freeze up.


How many feet of brake pipe do you need to replace the brake line.?

measure affected line


What does it mean when you are changing your rear brakes and brake fluid goes everywhere?

either a seal is damaged, a brake line broke or you did not use the correct tools to take it apart. Buy a car repair manual for the correct procedure..


Clogged brake line repair?

To fix a clogged brake line, first find the clog. Then, remove the clogged line from the cylinder. Attach a new line, and pump the car's brake to test it before driving.


How do you replace brake lines for a Honda accord?

Your question needs some clarification. If you meant to say how do you replace the front/rear flexible brake hoses (assuming you have rear disc) or how do you replace all of the brake lines on my Accord that would greatly help direct a more direct response. You should have specific hand tool before changing your brake lines, and that is a flare nut wrench. I have a 10mm and 12mm flare nut wrench that works well. This wrench if thicker than a standard wrench and one side is approximately 75% closed (like a box end wrench) to allow for more contact area and reduce stripping the flare nut. There are also clips that hold the line to a bracket where the 'hard' & 'flexible' lines connect. Leave this in-place until you have loosened the connector (and install the clip) before you tighten the connector


What are the Brake line schematics for a 1999 intrepid?

The 1999 Dodge intrepid brake lines schematics diagram shows the routing of each brake line. The diagram will show the brake line routing from the master cylinder to each wheel.


Can you use jb weld on a metal brake line?

replace brake line the damage to the line or if the jb weld gets into the line it will affect how the system works.


Where can I get instructions on how to repair the brake line on my car?

Chilton has a manual on home auto repair. The following website contains information that should assist you with brake line repair: autorepair.about.com/od/fixityourself/ss/brakeline_repl.htmCached - Similar


Can you cut off rear brake line?

You can cutoff the rear brake line. You will no longer have rear brakes and the fluid will leak out. It is not recommended that can't off the rear brake line, without replacing it.


What amount of money is the cost of brake line repair?

The cost of brake line repair is anywhere from 50.00 dollars and up. To repair the brake line it depends on who is fixing the car and what type of car you have.