0
What size Socket is used for the crank pulley of a 2.5 4-cylinder?
Wiki User
∙ 17y ago
it would be a 19mm or a 22mm
Wiki User
∙ 17y ago
Add your answer:
Earn +20 pts
What size socket is used for the crank pulley of a 2.4 4-cylinder?
22mm socket. Good luck!
What size is the crank pulley bolt on sr20?
27mm
What 1600 volkswagen bug crank pulley nut size?
30mm.
1998 Ranger 2wd 4cyl what size SOCKET for crank pulley I'm changing the timing belt....?
I have a 99 4 cyl std tranny ranger. the crankshaft pulley bolt is 22mm. Am having problem loosening bolt. need special to lock crankshaft. I have a couple ot things to try.
How do you remove a crank shaft pullie from a 98 Toyota camary?
You have to get a pulley puller of the appropriate size. Without a pulley you have no chance safely to remove it. Be careful do not deform the pulley it's not that hard as you can think.
What size socket to use to take off harmonic pulley for 1995 grand jeep Cherokee 5.2L?
1.25 inch
How do you remove the crankshaft pulley in a 1993 Geo Metro LSi 3 Cylinder?
There is a large metric bolt right (17 or 18mm) in the center of the main crank pulley. Immobilize the crank using a vise-grip equiped with a locking chain. Wrap an old fan belt (cut-to-size) around the crank and protect the serpentine gooves of the crank pulley, then wrap the vise chain and clamp onto the crank. Use a good breaker bar, or impact hammer to break the bolt torque free counter-clockwise. Note: Don't remove the four 10mm bolts on the crank pulley. The whole thing comes off as one assemble piece.
How do you fit a fiat punto 55 fan belt?
WORKING FROM THE FRONT; YOU NEED A SIZE 17 SOCKET ON A TBAR.THE ALTERNATER IS ON DRIVER SIDE AT THE BACK.THERE ARE THREE BOLTS TO LOOSEN (DONT TAKE THEM RIGHT OFF) . PULL THE ALTERNATER TOWARDS THE FRONT OF THE CAR, SLIP BELT OVER CRANK PULLEY THEN OVER ALTERNATER PULLEY .LEVER ALTERNATER BACK TO TIGHTEN BELT,THEN RETIGHTEN 3 BOLTS
1988 Nissan Z 2.4 cranskshaft bolt socket size harmonic balancer-ie. crankshaft pulley assembly center bolt?
27mm
What is the Caliper socket size for a 2002 Chevy Avalanche?
15mm Socket size.
What belt size is belt that just goes from the water pump pulley to the crank pulley on a sbc 350 engine?
There is not A belt that does that. It will be on the alternator too. If it is in the orriginal vehicle A parts store can get it for you by make, model, and options. If its not orriginal You will need to just try some different sizes.
How do you replace the serpentine belt on a 1995 Pontiac Grand AM?
Locate the tensioner pulley within the engine bay. It usually is near the top and middle of the engine, above the crank and fan pulleys. You can recognize it by noting that Avery other pulley in the engine bay has grooves that the servpentine belt rests in but the tensioner pulley is smooth and the belt rides on the smooth side of the belt. Once you find the smooth tensioner pulley, look at the middle of it. There will be a 6 point (hex) stud that you want to use a long-handled socket wrench upon. you may even need a breaker bar to get enough leverage to overcome the tensioners spring. turn the socket wrench in the direction which pulls the pulley away from the belt. there is a lot of force involved so don't let go or use the wrong size socket as it may slip possibly injuring you or anyone that may be helping you.You will most likely need another person to help you remove the belt and install the new one since you will be using two hands to releive the pressure of the pulley. After the belt is removed, you may slowly let the tensioner back down while you wind the new belt around all but the tensioner pulley. Carefully crank back the tensioner pulley until the belt can be sliped underneath the pulley and slowly release it back down upon the belt. Check to ensure the serpentine belt hasn't derailed from all the grooves from any pulleys. After that, starterup. Good luck. KrispyKreemD
