answersLogoWhite

0


Best Answer
Copy

inch and a quarter

or one and five sixteenths

User Avatar

Wiki User

โˆ™ 2011-09-03 11:56:02
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: What socket is needed for the front axle nut for the hub assembly on a 1994 Chrysler Concorde?
Write your answer...
Submit

Related Questions

What socket is needed for the front axle nut of hub on a 1998 Chrysler Concorde?

34 mm metric socket. They cost under teen bucks


Can you replace the lighter socket in the 2000 Chrysler Concorde?

yes


How do you replace the oxygen sensor in a 1995 Chrysler Concorde 3.3L?

With an o2 sensor socket.


What socket is needed for the front axle nut for the hub assembly on a 1984 Chevy pickup?

A 11/16 socket is needed to remove the 1984 Chevrolet pickup front axle hub assembly. The socket should be a five-point socket.


How do you change front turn signal light bulbs on 2000 Chrysler Concorde?

Reach in from the bottom of the fascia. The socket takes about a quarter turn.


What is the socket size needed to remove the drive axles on a 1997 Chrysler lhs?

1 5/16 in


What size socket is needed to change spark plugs on 1987 Chrysler lebaron?

13/16 inch


How do you change camshaft sensor 2004 Chrysler Concorde?

The Crank position sensor is located on the right side behind the wheel about midway up the motor eaiseier to get to from the bottom with 10mm socket one bolt


How do you replace the battery in a 2001 Chrysler Concorde?

Remove Air box assembly, and Right front wheel. There is an access panel into the battery compartment, remove using 6mm socket. Battery is held down by a bracket 10mm and a long extension. Remove battery cables 1 at a time and pull battery through access panel in fender well.


How does it change rear window brake light on a 2004 Chrysler concorde?

I just replaced a blown third brake light bulb today. ... I have about 60k on my M and havent yet had to change the brake light---so if it only has to be done once in the ... If memory serves, the Concorde's is in the rear window. ... Well I decided to mod my 2004 300Mspecial Third Brake lights, not with a bulb ...


What size socket is needed for castle nut on front hub assembly of 2004 dodge ram 1500?

1 11/16 or 43mm


How do i Replace the rear blinker bulb in a Chrysler 300?

In the trunk compartment, pull back the carpet covering the inside of of rear light assembly. Unscrew the three wing nuts, don't loose these! Pull the entire assembly out and unscrew the light socket from the assembly replacing he bulb and reassemble in reverse order.


How do you change spark plugs on a Chrysler 300?

The spark plugs on a Chrysler 300 are changed by removing the plenum assembly, pulling the plug boots, and removing each plug using a deep wall socket. The gap of each new plug is set and installed into the heads.


How do you disconnect the wiring connector from the headlight bulb socket on a 2000 Chrysler voyager?

To disconnect the wiring connector from the headlight bulb socket on a 2000 Chrysler Voyage, remove the wiring that goes into headlight plastic lock ring. Snap it loose and pull out the bulb socket.


How do you replace the headlight assembly on a 1997 Dodge Neon drivers side I seem to have everything loose but there is something that is not releasing and I don't have a manual.?

I have a 1997 Plymouth Neon. The way to replace the headlight bulb is: 1. open hood, and disconnect the wiring connector from the headlight bulb socket. 2. Turn the bulb socket retaining ring counterclockwise and remove the bulb and socket assembly. 3. Pull the bulb out of the socket assembly. 4. Reinstall the bulb and socket assembly in the light housing. Turn the retaining ring clockwise to secure the bulb in the housing.


How do you replace headlight assembly on a 1999 Pontiac grand prix?

There are two 10 mm bolts that are on top of the headlamp assembly. Remove those bolts. Then gently pull the assembly out of the frame of the vehicle. Remove the wire harness, and the lamp assembly. Then there are two plastic threaded 10 mm bolts that need to be removed..a deep well socket will be needed for this, as well as a 10 mm nut. It can be removed with the same socket. Then the headlamp will be separated from the "turning light". To install, just do the opposite.


How do you change the left blinker light on a 1995 Toyota Camry?

There should be a screw or two holding the directional assembly to the fender. The back of this assembly has a light bulb socket which usually comes out by turning it just a little to release the tabs on the socket from the slots in the assembly


Your spark plug socket will not fit onto the spark plug on the 5 cyllinder on your 1994 Chrysler 3.5 liter engine Is there a special tool needed to remove this plug?

no, it takes the same socket as the others. most likely something is down in the hole next to the spark plug


How do you replace headlight bulbs on a 2001 Dodge Intrepid?

Directions straight from the owner's manual. 1. Open the hood and remove the headlight assembly mounting screws. 2. Pull the headlight assembly forward to access the bulbs. 3. Turn the bulb assembly retaining ring counterclockwise and pull the bulb and socket assembly from the housing. 4. Remove the bulb from the socket and replace the bulb. 5. Reinsert the bulb and socket assembly and turn the retaining ring clockwise to secure the bulb. 6. Reinstall the headlight assembly.


How do you replace a license plate light on a Chrysler Town and Country?

Unscrew light from bumper. Turn socket 1/4 turn counterclock. Pull socket out of cover. Pull bulb out of socket.


Where is the headlight socket located on a 1996 cavalier?

It is at the rear of the headlamp assembly where the wires are.


What size star socket is needed for the calipers on a 1995 Mercury Villager?

Torx T 40 socket


How do you replace the spark plugs on a Chrysler town and country?

Remove the spark plugs with a 5/8 deep well socket. Turn the socket to the left. Tighten the new spark plugs by turning socket to the right.


What size Allen socket is needed to remove caliper bolt on a 2004 Escape?

What size Allen socket is needed to remove bolt from caliper on 2004 ford escape


What is the socket size for a 1997 Chrysler lhs spindle nut?

1 5/16 inch