best to read up on it..
everyone should have a manual for their vehicle, and the library should have a professional manual available...in the reference section, you'll have to make copies of the important sections...good luck :)
It takes a ten millimeter to remove that bolt and it is hard to get to
how to remove crankshaft position sensor from 91 Buick Regal
Press off the balancer .
You have to remove and disassemble the engine to replace the crankshaft.If you mean the crankshaft position sensor, then yes. You access it from underneath. It is just above the oil pan on the back of the block.You have to remove and disassemble the engine to replace the crankshaft.If you mean the crankshaft position sensor, then yes. You access it from underneath. It is just above the oil pan on the back of the block.
Hello! The crankshaft position sensor is located behind the crankshaft pulley,on the left side facing the front of the car.It is difficult to see and to remove it you need to remove the crankshaft pulley ( radiator,belts,.... )
The crankshaft position sensor is located right above the starter, you may have to remove the starter for better visibility.
Disconnect the negative battery cable.Remove the air cleaner housing.Disconnect the crankshaft position sensor harness connector.Remove the retaining bolt and the crankshaft position sensor.Reverse procedure to reinstall.Are the Crankshaft sensor and the Crank snsor the same?Please let me know?
Crank position sensor is located next to the crankshaft. In order to replace it you might have to remove the timing belt. In the most models you just can remove remove the timing belt cover and replace the sensor.
Remove the engine brush cover under the front of the engine. Remove the drive belt to make changing the sensor easier (optional). Remove the lower timing belt cover and the crankshaft pulley to access the crankshaft position sensor. Disconnect the electrical modules from the crankshaft position sensor, located next to the alternator. Take off the bolts with a socket wrench and remove the sensor.
The crankshaft position sensor in a 2002 Jeep Grand Cherokee 4.7 liter is located left of the starter. In order to remove the crankshaft position sensor the CKP mounting bolt will have to be removed first.
The 1997 Chevy Malibu crankshaft position sensor can be found on the back of the engine. You will need to remove the rear engine cover in order to access the crankshaft position sensor.
opel omega crankshaft sensor is located next tp the oil filter atached with a star shaped screw, to remove it you have to remove the oil filter first. or the muffler.
The 1994 Volvo 850 crankshaft position sensor can be found on the back of the engine. You will need to remove the rear engine cover in order to access the crankshaft position sensor.
Do nothing. There was no such thing in 1967.
It is behind the starter, Will have to remove starter to get to it.
remove the engine and transmission from the car, then remove engine flywheel and it will be right there
24x crankshaft position sensor--remove drive belt, raise vehicle up in front ( car ramps etc. ) remove the crankshaft pulley, remove the bolt and sensor wiring harness retaining bracket. remove the 24x crank sensor mounting bolts, remove the sensor and withdraw the wiring harness. for 3.1 V6 the 2.2 has a 7x position sensor. good-day !
CRANKSHAFT POSITION SENSOR The crankshaft sensor is located on the passengers side of the transmission housing, above the differential housing Crankshaft Position Sensor The bottom of the sensor sits above the drive plate REMOVAL Disconnect electrical connector from crankshaft position sensor. Remove sensor mounting screw. Remove sensor. INSTALLATION Install sensor and push sensor down until contact is made with the transmission case. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque. Connect electrical connector to crankshaft position sensor.
It is behind the starter. You will have to remove the starter to service it.
The crankshaft position sensor is located behind the crankshaft pulley and harmonic balancer. A writeup of how to remove with pics can be found in the article for a camshaft install. check out: http://www.clubgm.com/cam Hope this helps. "G"
The HyundaiÊ1.3 liter engine crankshaft position sensor can be found on the back of the engine. You will need to remove the rear engine cover in order to access the crankshaft position sensor.
the crankshaft sensor is above the oil filter on my 00 neon. it has one 10 mm bolt that needs taken out to remove the sensor
The 2000 Mercedes-Benz E3 20 crankshaft position in sensor is located on the back of the crankshaft. You will need to remove the rear engine cover in order to see the sensor.
there are 2 aluminum shields on the right hand side of the of the engine remove the 3 screws from the top shield and remove it .you will see another little shield under the pipe once you remove the 1 screw from the little shield you will locate your CRANKSHAFT POSITION SENSOR its pretty easy to reach from under the vehicle.
under the car with extention and universal, with a 11 mm.