answersLogoWhite

0


Best Answer
Copy

Use a 10mm Socket to remove the bolts And then use a c Clamp to depress the piston but make sure that the brake fluid cap is off first, While pushing the piston in turn slowly or else you will mess up the Master Cylinder because i have the same car and i just had that problem.

User Avatar

Wiki User

โˆ™ 2006-08-17 20:36:06
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: What tools socket sizes etc are needed to change the front brakes on a 1997 Cirrus?
Write your answer...
Submit

Related Questions

What size socket is needed to replace the rear brakes pads on a 2001 Sportster XL 883?

A twelve point 1/4 inch socket.


How do you change brakes on 2006 Ford Escape?

what can the socket use to take the bolt for breks pad


What kind of socket is needed to change the oxygen sensor on 97 dodge caravan?

It is called an oxygen sensor socket.


What tools are needed to change brakes on a 1995 Isuzu rodeo?

14 mm wrench or socket--top bolt does not loosen--take out bottom bolt and snap out pads -- front and back of each wheel


What size socket is needed to change spark plugs in 5.4liter engine?

youll need a 5/8 superdeep plug socket


What size socket wrench to change brakes on 96 cavalier?

You need a 3/8 Allen key to release the caliper.


What tools are needed to change the pads on a 1994 Eclipse?

socket rench and a c-clamp


What tools are needed to change brake pads on a 1998 Chevy Monte Carlo?

ratchet or socket


What size socket is needed to change spark plugs on 1987 Chrysler lebaron?

13/16 inch


What is the spindle nut on 2000 ford focus rear drum brakes?

Nut you see after you remove the dust cover, in the middle of the drum, 30mm socket needed to remove


What size wrench is needed to remove the caliper bolts on the front brakes of a 99 Pontiac sunfire?

You need a 3/8" allan key or hex socket - not a torx


Does it require a special tool to remove the brakes on a 2003 Ford Expedition?

There are not any special tools needed to remove the brakes on your 2003 Ford Expedition. You will need a lug wrench, a 9/16 socket, a screwdriver, and a needle nose pliers.


Tools needed to replace 2005 Nissan Xterra front brakes?

the only tools need are a 17 inch socket a rachet a "C" clamp to push the piston back in.


What tools are needed to change the brakes on a 2004 Mazda 6?

Metric combination wrenches, socket set,possibly metric Allen wrench set, jack stands and hydraulic jack. Get a Haynes manual also available at NAPA parts stores.I hope this helps.


What tools are needed to change the brakes on a 1997 town car?

Lug Wrench to remove tire & Wheel Socket Wrench or Hex Wrench to remove Caliper bolts Large "C" clamp to collapse caliper piston Rags, and a good spray brake cleaner


What size caliper socket do you need to change the front brakes on a 1995 GMC Vandura 3500?

Most likely 3/8 Allen for caliper this truck.


What tools are needed to change the lower control arm on a 1989 Chevy Cavalier?

You will need a one inch socket and ratchet. You also might need a mallet. The socket and ratchet will be needed to remove the lower control arm nuts. The mallet might be needed to loosen the control arm.


I Need a list of tools to change front brakes on 2004 Chevrolet 1500 Z71 4wheel drive?

all you need is a socket set and a c.clamp drive safe


What size Allen wrench do you use to change front brakes on a 2000 cougar?

You need a torx type socket. If you use an Allen wrench...you will strip out the inside of the bolt.


How do you Replace drum brakes on 93 f150?

You have to get a special socket at the auto store.


What tools are needed for oil change?

The tools needed for an oil change tend to be common tools. A floor jack is needed to access the oil pan. A pan which is used to drain oil into. A wrench and socket set is used to remove and replace the oil cap.


What socket is needed for the front axle nut for the hub assembly on a 1984 Chevy pickup?

A 11/16 socket is needed to remove the 1984 Chevrolet pickup front axle hub assembly. The socket should be a five-point socket.


Does anyone know what size torx socket is needed for the upper attachment brackets to change out the rear door strut supports on a 1996 Grand Cherokee Laredo?

Hi- The numbers on my socket are "E8 S-K"


What size wrench is needed to remove the caliper bolts on the front brakes of a 1995 Chevy Suburban?

the caliper bolts require a 3/8" Allen wrench. You can buy these as a socket at just about any parts store.


What size star socket is needed for the calipers on a 1995 Mercury Villager?

Torx T 40 socket